Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

refinishing question

Posts

refinishing question

#1

refinishing question

john lucas

I bought this leather topped walnut desk for my office and plan to refinish it. I have 2 problems. Alcohol and lacquer thinner won't touch it so I assume it's a polyeurothane finish or something similar. Here is my problem. It's in pretty good shape and I was hoping to just apply some more finish over this with just a very light sanding. The problem is the drawer hardware. I have been unable to find 64mm hardware that has what I'll call a round support plate that is 1" in diameter. Everything I can find is smaller than this. Is there anyway to get rid of that ugly black ring left from the previous hardware or am I going to have to strip all the drawers back to bare wood. The other hardware was damaged and some of it was missing which is why I can't just reuse that. I sanded away the outer ring left from the previous finish and there is a black tarnished area I assume left from the brass interaction with the woodl.


Re: refinishing question

#2

Re: refinishing question

Barry Irby

A few weeks ago I asked about removing black water rings and someone suggested Oxalic acid in the form of Bar Keepers Friend. I found it in Kroger's and also in Lowe's. The video suggested mixing up a paste and coating the affected area. The thing they showed had a big blotch. Worked perfectly in the video. I tried it and was a bit Cavalier slopping it on. Left it for a few days. It helped lighten the black stuff, but not as much as in the video, but, it also lightened the surrounding area. So now I have a dark ring surrounded by a light ring.

If you try this, be a little more artistic than I was and touch only the dark area.

How about some kind of back plate?

Re: refinishing question

#3

Turn wood baseplates and make the pulls

Dick Coers

You might be able to find someone with a lathe?

Re: refinishing question

#4

Re: refinishing question

CharlieL

Out of curiosity, can you post a picture of one of the complete pulls that came with it ? You may want to try looking through the Van Dykes website, or their catalog. http://www.vandykes.com/knobs-pulls/c/20/filter/100000013267eq100000013256/

Re: refinishing question

#5

Re: refinishing question

John K Jordan

How about a flat rectangle (with some edge treatment) to extend over both spots and mount whatever hardware to that?

JKJ

Re: refinishing question

#6

Re: refinishing question

john lucas

Been through Van dykes, Rockler, Woodcraft, Lee Valley and several other sites that just sell hardware. The problem is non of them tell what size the circular part is. They just tell what distance the screw heads are. I bought some from Lee Valley and that's what started all of this.

Re: refinishing question

#7

Re: refinishing question

john lucas

John That will be my next route is to make some thin brass washers and patina them to roughly match what I bought from Lee Valley.

Re: refinishing question

#9

Re: Horton brasses

john lucas

Thanks Dick. Exactly what I'm looking for. Now have to decide if it's worth that much money. I only paid $50 for the desk. Those handles will run about $100.

Re: refinishing question

#10

Kneale Brownson

How much is your refinishing time worth?

Kneale Brownson

If you're going to end up with a nice-looking and sturdy desk, go shopping for a new one. Your extra $100 investment will pale by comparison.

Re: refinishing question

#11

Re: refinishing question

Hank Knight

John,

This is probably an impractical reply, but if you are planning on visiting Washington DC in the near future, there is a place there that sells reclaimed furniture hardware and architectural pieces. It is a treasure trove. They have drawers and cabinets full of every kind of drawer pull imaginable. All that's required is a little time digging through their amazing stock to find exactly what you're looking for. I've fotgotten the name of the place, but if you're interested, I can easily get it and the address from my daughter who lives there and first pointed the place out to me.

Hank

Re: refinishing question

#12

DC place

Gary Smyth

There is a place called The Brass Knob. In DC proper. Purple building. Nice stuff, good selection, but not for the faint of wallet. So many dual income, high pay couples around that the store can go wild and buy lots of stuff fifty miles out of town, ship it in, triple the price, and sell. Solid business with "Interior Coordinators" as well as national media/entertainment productions who essentially have large budgets for architectural goods/focal points/sets. I think that the production companies either write it off, or then sell it back if not destroyed. For them the cost of doing something visual. It's been a while since I was there, but I can't imagine that they don't have online sales.