Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

anybody use a 15 ga finish nailer much?

Posts

anybody use a 15 ga finish nailer much?

#1

anybody use a 15 ga finish nailer much?

Tim Greif - West of Chicago

Found a decent deal on a 15 ga Hitachi angled finish nailer. But am wondering how much I'd use it. I use an 18 ga brad nailer a bunch in woodworking, but aside from installing base molding or door/window casing, I'm wondering how much I'd really use it.

Re: anybody use a 15 ga finish nailer much?

#2

Re: anybody use a 15 ga finish nailer much?

Thomas Skaggs, Foothills of Mount Level

I don't use a nailer very often. Where I tend to used them is in the construction of furniture in "no show" places. But even then I just use the brads to keep something in place and free up my hands so I can complete that assembly with better fasteners.

T.

Re: anybody use a 15 ga finish nailer much?

#3

Re: anybody use a 15 ga finish nailer much?

David Bair

Besides the trim work you referenced, I've used mine to set pre-hung doors before using long screws through the hinges for a more permanent installation.

Re: anybody use a 15 ga finish nailer much?

#4

Trim Gun

Mark Mandell - Gone Round In New Jersey

I use mine (a Bostich oil-free) when doing both interior and exterior trim. I also use it where I don't want a big nail showing such as in siding and seating surfaces. Bought a few boxes of stainless nails years ago for working with treated lumber, but am about out and can't seem to find them in the stores.

Re: anybody use a 15 ga finish nailer much?

#5

Re: anybody use a 15 ga finish nailer much?

Bill Tindall, E.Tn.

It is perfect for installing house trim. Never had a need to use one for furniture.

Re: anybody use a 15 ga finish nailer much?

#6

If you don't have a 23 gauge

Gary Smyth

I'd look to that before a 15 -- especially if you have a 18 gauge. I took a chance on a Grex and it has turned out to be one of my better purchases.

Re: anybody use a 15 ga finish nailer much?

#7

Re: anybody use a 15 ga finish nailer much?

Dave's Not Here

You won't need one until the day after you pass on that Hitachi. :)

Re: anybody use a 15 ga finish nailer much?

#8

Re: anybody use a 15 ga finish nailer much?

Barry Irby

I have one that shoots 2 1/2 inch nails. Use it a lot in remodeling houses. Base, casings, shoe, etc. Can't remember ever using it in the shop in furniture.

Re: anybody use a 15 ga finish nailer much?

#9

Re: Trim Gun

Keith Newton

I've got the same one as Mark, but have worn out several Senco SN1s and SN2s, before switching. When I bought the first Sencos, they would repair them free, as long as we bought their fasteners, but eventually the repair parts cost more than just buying a new nailer.

If you were a trim carpenter, you couldn't last long in business without this size gun.

Re: anybody use a 15 ga finish nailer much?

#10

Gun Erl

Mark Mandell - Gone Round In New Jersey

Both of my trim/finish guns are oil-free (the Bostich N62FN and the Senco FinishPro 25) which was important to me as I didn't want to deal with oil spots on the wood. Both have been consistent performers and the only jam I think I ever had was trying to drive a 2" brad through a piece of Hickory :b

Re: anybody use a 15 ga finish nailer much?

#11

Re: Gun Erl

Barry Irby

Many years ago I was on top of a ladder with my Senco finish nailer and managed to shoot a nail through my left index finger. Luckily it was a flesh wound. Nail went beside the bone and was sticking through it like an arrow. I climbed down the ladder thinking "Somebody is going to have to pull that out". My helper Charlie was as green as grass. Never saw anyone else that green. Decided "Its not going to be Charlie". Snatched it out as fast as I could. Put a band-aid on it and went back to work. Never even hurt. Now I know why they used to advertised the nails were sterile.

Re: anybody use a 15 ga finish nailer much?

#12

Nailed

Mark Mandell - Gone Round In New Jersey

I seem to remember a stat to the effect that there is not a single part of the human anatomy that hasn't been power-nailed more than once.

Re: anybody use a 15 ga finish nailer much?

#13

Re: Nailed

Barry Irby

I have been using nailers and staplers for forty years or more and that is my only injury. I had a near miss in the same house. Kneeling on the floor I leaned over the edge of an opening and shot a nail back up through some trim. The nail came trough the floor and touched my kneecap. I was shaken, realizing I had just about nailed myself to the floor. Had to have a few minutes to think it over.

Still do not understand how that nail went through my finger.

Re: anybody use a 15 ga finish nailer much?

#14

That reminds me of a favorite story,

Keith Newton

The rep that sold me my first guns would come around to the job sites every couple of weeks. One morning he came in chuckling about hearing panic yelling from the garage earlier when he got out of his car on another job site. He ran in to find the carpenter who had been hanging panelling had stapled his finger to the wall. If that alone wasn't bad enough, he was just tall enough to reach 8' if he sort of lunged up on tiptoes, and hit it just right. Well, there he hung by one finger up on tiptoes, with no nail apron.

Bud ran out to his truck, got nippers, and cut him down. Fortunately it had just happened, so the damage was minimal, other than the bitter taste of humiliation that I'm sure lingered a while. ha

Re: anybody use a 15 ga finish nailer much?

#15

Re: 40 Years Ago

Mark Mandell - Gone Round In New Jersey

Back then I used a 24oz/16" checker-head framing hammer. We used to have contests to see who could send the most 16d's home with the fewest swings. My best finish was 2nd in a 4-man crew, and I think they let me have that one.

Still have the hammer; haven't touched it in 20 years.

Re: anybody use a 15 ga finish nailer much?

#16

Re: 40 Years Ago

Barry Irby

I had one of those. Had a custom made right handed handle that was about 20" long with finger grips. Little finger hung off the end. It looked like a saber when I wore in in my tool belt. (I'm 5'7") It came close to dragging the ground. Set the nail with a tap and drive it home with a single stroke. People teased me endlessly about it, but three of them were stolen. Wish I still had the last one. My best friend's father made the handles.

Re: anybody use a 15 ga finish nailer much?

#17

Kneale Brownson

Re: 40 Years Ago

Kneale Brownson

I swung one of those for a couple days when I was assembling the 8'X8' 2X6 wall sections I put on top of the 3 feet of block for my barn walls. My arm/elbow got so sore I couldn't lift a gallon of milk and pour it into a glass. That's when I bought my first framing nailer. I just realized that was almost 45 years ago.

Re: anybody use a 15 ga finish nailer much?

#18

Re: 40 Years Ago - Today

Mark Mandell - Gone Round In New Jersey

I still have the hammer. It hangs in the rack to remind me of those pre-framing gun days.

Re: anybody use a 15 ga finish nailer much?

#19

Re: 40 Years Ago - Today

Barry Irby

I got a framing nailer fairly early on in the emerging nail gun days. It was interesting. Everybody instantly forgot you could actually pound a nail with a hammer. They just stood around and waited for the guy with the nail gun.

In those days we called smokers "one arm workers" because they were always fiddling with a cigaret with one hand. The mason that worked for me would not hire a pipe smoker. Said he already had a full time job. Almost glad he did not last long enough to see cell phones. No arm workers. Workers may be the wrong word.

Re: anybody use a 15 ga finish nailer much?

#20

Elbows

John in NM

I had an elbow injury after a short framing job maybe 6 years ago - swinging a framing hammer at chest height did me in. Took months of frequent icing to get that elbow to heal.