Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

rip blade

Posts

rip blade

#1

rip blade

Bruce, a MN Galoot

what is a really good 10" rip blade? Does a glue-line rip work just as well for ordinary ripping duties?

I had a thin kerf Freud rip for my last saw that worked just fine, but that was an 8" and I'd prefer a thicker blade anyway.

Thanks.

Re: rip blade

#2

Re: rip blade

Mark Mandell - Gone Round In New Jersey

I've used several blades in my saw, but for straight ripping, nothing has equalled my Systematic Glue-Line Rip. This is a full kerf blade so I would not use it to cut heavy hard wood with less than a 3hp saw.

That said, I've had nice cuts in 3/4" stock using a 7-1/4 blade, but the cut face was not as smooth as the Syst'y so I always tweeked them on the jointer.

Re: rip blade

#3

depends on your ripping needs

Bill Tindall, E.Tn.

the saw blade companies seem to stay in business so I make the assumption that any will work just fine. Buy what ever brand is readily available.

Lots of ripping of 8/4 stock- 24 or less tooth

Glue line ripping- buy lots of teeth "glue line rip" but it will bog down in heavy stock

routine ripping of 4/4 - A quality (not a framing blade) 7 1/2 " combination blade does great. I use CMT.

Re: rip blade

#4

Re: rip blade

Lee Schierer in McKean, PA

I switched from a Freud thin kerf to their full kerf glue line rip and I've been impressed. I have a 1-1/2 Hp Craftsman and it easily rips 3/4" maple, oak and cherry with a nice smooth finish and no burning. Of course you need a well aligned saw.

Re: rip blade

#5

Re: rip blade

Robin Corell in Atascadero, CA

I have an Amana industrial quality glue line rip that has a kerf of just under .150" and it has been a fantastic blade.

Re: rip blade

#6

Freud LM72R010

Tim Greif - West of Chicago

I really like this blade for ripping any solid wood. Has a flat top grind so will make really flat bottom grooves if desired. Very smooth cuts. Full kerf blade.

Re: rip blade

#7

Ditto and...

Grant in Iowa

I too like this blade. Freud makes great blades that are widely available, and local resharp services can readily set up to sharpen them since they are common.

I have one of these blades, but I also have a Freud LM74M010, which is a 30 tooth blade without the red coating. Slightly better finish due to more teeth, and yet a slightly lower cost because it lacks the fancy coating.

On the red coating, I find little use for it in my shop. I seldom touch wood to the plate of the blade, as I usually work with hardwoods, not construction grade lumber. I'd rather have more teeth for my money. Further, the chrome colored blades are easier to do accurate run out measurements, since there's no paint in the way.

They both work well, and can produce a glue line surface.

One more note: If you have your saw precisely aligned and set up, endeavor to do precise work, read on. The silk screened lettering on these blades can throw off your blade run out significantly if it gets between the saw arbor flange and the blade. I take a razor blade and scrape off the lettering in the area of the arbor before using. This ensures the blade sits flat against the arbor flange on my Unisaw.

I know this sounds crazy, but the lettering is maybe .002 thick, but its location is like placing a shim in one location between your arbor flange and the blade. The issue can cause the outer surface of the blade plate to have run out up to .008 or more, since the "shim effect" is magnified at the outer edge of the blade.

Doubt me? I showed this to a Freud regional sales rep and he measured it with me using a dial indicator before removing the label and after, and he agreed that this is clearly an issue. He even said that the last thing to go on the blades in the hands off factory is the screen printing. Claimed he'd take it up with corporate. I see nothing has changed on the blades though. You'd think they'd make a change, as with .008" of run out, you can see the finish difference.

Regards,

Grant in Iowa

Re: rip blade

#8

Re: Ditto and...

Bruce, a MN Galoot

8 thou is a lot of run-out, no doubt. I was unaware of this problem and will definitely look for it. My saw is set up very well, and the quality of a rip is important to me. I only have two combination blades, one of which is a top rated Freud, but its cut is so fine it's not very good for rip. My last combination blade was a Systimatic, which was an absolute joy to use. Had it for 30 years, but it was pretty well shot and although still sharp, I gave it along with the saw it was on to my brother who doesn't use it very much.

Re: rip blade

#9

Thanks everyone for the help

Bruce, a MN Galoot

One of the guys here made a very good offer of a virtually new Freud rip blade. It will come just in time for me to begin making a cabinet for a friend who has a whole stack of air dried cherry.

Re: rip blade

#10

Re: Thanks everyone for the help

Bill Tindall, E.Tn.

The prettiest cherry in terms of grain and color I ever saw came from southern MN.

Re: rip blade

#11

Re: Thanks everyone for the help

Bruce, a MN Galoot

I made a dining table for these friends from the first half of the stack. Some was pretty good. They just hadn't cut any dimension stock, much was barely an inch thick. But it was nice to work with. I had a local cabinet shop shoot it with conversion varnish.

Re: rip blade

#12

Re: rip blade

TomD

When I started out I always saw rip blades with a square tooth which makes them versatile for certain joint cutting tasks and certain dado tasks. Then one time I bought one and the teeth were alternating top bevel. Doesn't really affect ripping on a powerful saw, and I guess the idea is you can do some crosscutting with it also. For myself I prefer the flat top, so that is on my list.