Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Hinge for a drop leaf table???

Posts

Hinge for a drop leaf table???

#1

Jesper, Denmark

Hinge for a drop leaf table???

Jesper, Denmark

Moving to the apartment from a spacious house, the dining area also is the main thoroughfare in the apartment, so the old dining table table has to be remodeled to a much smaller size. The length will be reduced to 48" fro 75" and the width to a measly 30". OK for two people across from each other, but very squashed for four.

My thought is to make a drop-leaf from the cut-off for one end, which will normally be under a window sill. This will allow four to eat comfortably. 99% of the time, there are no more than two eating at the table.

So the question is: What is your favorite hinge for the drop leaf? It seems to me that a piano hinge would work well.

------------------

In case you are curious, the table will butt one end under a window sill and the other end needs to leave passage way past a half wall into the kitchen, so that two people can sit and commune with the cook, rather than one have his or her back to the kitchen.

Re: Hinge for a drop leaf table???

#2

Sounds like you need a rule joint hinge


Re: Hinge for a drop leaf table???

#3

Re: Hinge for a drop leaf table???

John in NM

Either rule joint hinges or standard butt hinges, so long as they are mortise hinges and fit well in their mortises. I prefer to avoid piano hinges for applications that fold down rather than up, but in all honesty one would probably work fine for this as well.

Re: Hinge for a drop leaf table???

#4

Re: Hinge for a drop leaf table???

Gary Smyth

You might also look into a Butler's table hinge. Soss makes a barrel invisible hinge. This will depend on the thickness of the wood. How do you intend to hold the leaf up when it is lifted to increase the table size? Both of these will permit a flush table top, but provide no locking mechanism to hold the leaf.

Re: Hinge for a drop leaf table???

#5

Re: Hinge for a drop leaf table???

William Duffield

Rule joints are kind of tricky to make and install, but well worth the effort. Their advantages are that the cove and bead in the leaf and top support the leaf when it is up, so there is insignificant load on the hinges and their screws. The other advantage is that the rule joint keeps crumbs and spilt milk out of the hinges. When the leaf is down, it's easy to clean out the joint. Properly installed, the hinges are invisible (except from the bottom, of course).

If you want to try it, I have a couple of documents and some diagrams I can send you that should help.

Re: Hinge for a drop leaf table???

#6

Re: Hinge for a drop leaf table??? *LINK*

Jim Dillon

Jesper, check out the latest edition of FWW (#255 July/August) for Chris Gochnour's drop-leaf table. It is in the Shaker-style. He provides an excellent description of the construction details, including rule-joint. He uses three Horton Brasses H-510 hinges. Jim


Drop Leaf Table Hinge

Re: Hinge for a drop leaf table???

#7

Re: Hinge for a drop leaf table???

William Duffield

Jesper, would you please PM me with a valid e-mail address. Gmail bounced the address in your profile.

Re: Hinge for a drop leaf table???

#8

Jesper, Denmark

Re: Hinge for a drop leaf table???

Jesper, Denmark

The leaf will be held up with simple wood sliders, located under the top and located with cut-outs in the trestle cross member and in an additional brace under the middle of the table.

Re: Hinge for a drop leaf table???

#9

Jesper, Denmark

Re: Hinge for a drop leaf table???

Jesper, Denmark

I do not know why e-mail is misspelled in the OP, as it is correct in my profile. Anyway, it is jgronvaldt@gmail.com

Re: Hinge for a drop leaf table???

#10

Jesper, Denmark

Re: Ruled out the rule joint.......

Jesper, Denmark

So it became a standard butt hinged with an off-set pin, so no need for mortises either.

There is a little story attached to this table. It originated around 1995, when I moved my office into the basement and need a work/computer table in a hurry. Quick, pick the WORST planks of black locust in the stack and glue-up the top with the least embarrassing side up. A simple trestle with a little G+G influence and a stand for the PC box completed it.

The top turned kinda "interesting" with some sapwood, some worm channels and a lot of different figure. The table moved along when I left the US in 2002 and has served as a kitchen dining table till recently - with the PC stand removed.

At 102 x 36 inches, it is way too big for the apartment, so now it is reduced to 46 x 30 inches with an 18" leaf and a new simpler trestle. The trestle will look weird for a year or so till it mellows in color like the old top. All the wood came from the two logs milled i Exeter, NH in the 1990's - after they had been "maturing" in the sawyer's field for who knows how long.

I think it is clear that a rule joint would be out of character, so keeping it simple goes along with the "interesting" top. The new elm work table is the same height and width, but 63" long, so they can be put end-to-end and have room for seating 10.