Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Bandsaw tires

Posts

Bandsaw tires

#1

Bandsaw tires

paul in AZ

The tires on my 10+ year old Jet 18" disintegrated in a wondrous shower of rubber pieces.

So~ new tires.

With nobody able to shed light on choosing between the blue vs. orange brands I got orange. Swing factors were $20 cheaper and I like the color.

Is there a decent reason to choose one over the other? Or are they all the same?

Should the blade be detensioned after use with urethane tires? I mostly don't.

Something I learned from a tool repair man today. He said the recommended 140 degrees F. water bath for softening the tires was way too cool. [I now agree]. He actually boiled his tires for 5 or 10 minutes. I thought that might be harsh so settled for pouring boiling water over one tire and letting it sit for ~5 minutes. I struggled mightily with the first tire soaked at 140 but the second [with boiling water] softened nicely and installing it was much easier.

Re: Bandsaw tires

#2

ebd

Re: Bandsaw tires

ebd

I de-tension after use always. I got a tension crank and that makes it fast and easy.

Re: Bandsaw tires

#3

Re: Bandsaw tires

David Frame

Paul,

I changed my 14" Delta band saw tires with the blue Carter Brand. The Carter tire is only 7/8" wide. My band saw wheels are a full 1" wide. They work, but I had a lot of trouble with the tracking of saw blades less than 1/2" in width. I called Carter and was asked if their tire had a radius between the width after being installed. If they did, I needed to make them flat for small width blades. I was aware of that issue because I've used the practices I read in the Band Saw Handbook by Mark Duginske years ago and addressed it when I installed them. Carter said they to take no responsibility for blades not tracking correctly. That's understandable. The wheels should be in-line with other and that takes a bit of aligning. All blades half inch and above worked fine. I eventually bought the orange tires and they are a full 1" wide and less expensive. Since then, I've had no trouble with any size blade from 1/8" to 3/4" in width.

By the way, I use a 3/8" dowel to stretch the tires on my wheels and always remove the tension on the blade when I'm finished using it for the day. However, expanding them in hot water is a great idea. I'm sure they shrunk tightly on the wheel after cooling.

Hope this helps,

David Frame

Re: Bandsaw tires

#4

Re: Bandsaw tires

paul in AZ

These tires are the full 1 1/2" wide.

One thing I have noticed while running the saw [but not using it yet] is that the blade will drift to one side of the tire if tension is looser but will ride on the center if properly tensioned. This with a 5/8" blade.

Re: Bandsaw tires

#5

Re: Bandsaw tires

David Frame

Paul,

I had the same problem with my band saw. First, remove power cord and any parts plus the blade that may get in your way while aligning the wheels. Second, place a good straight edge between the two wheels. Use the adjustment that tilts the top wheel to make it in-line with the bottom wheel. If one wheel is further back or forward of each other, you may have to add or remove (depending on how many washers are on the wheels arbor) a washer to get them aligned properly. After that, replace all parts removed and add the blade. Tension the blade properly. Turn the wheel by hand to see if drifts towards the edge of the wheel. Even though the wheels are now aligned, the tilt mechanism at the top wheel may still need minor adjusting. I always remove the tension off the blade when the band saw is not in use.

I wish I had an illustration or draw it in ACAD show you, but if you understand the directions I gave you, you'll do fine.

Remember this. Nothing is perfect, but you can get close.

D. Frame

Re: Bandsaw tires

#6

Re: Bandsaw tires

jerry roberts

Paul,if I remember correctly when I replaced my Jet tires nothing worked to get them on until I put them in already boiling water for abt 5 minutes I think. Not sure of the time but they went right on after that.

Re: Bandsaw tires

#7

Re: Bandsaw tires

paul in AZ

Yes. The insert that comes with the tires has a temperature recommendation that is quite inadequate. Pouring boiling water over the tire and letting it sit for several minutes was the answer.

I hope I can remember to do that years from now if/when I have to change tires again.

Re: Bandsaw tires

#8

Re: Bandsaw tires

Mark Mandell - Gone Round In New Jersey

I've had my JET 18 for 17 years and the original tires are just fine.

What are youz guys cuttin' what rots your rubber?

Re: Bandsaw tires

#9

Re: Bandsaw tires

paul in AZ

I just looked up the receipt. The saw is a bit over 14 years old.

Being in Arizona doesn't help. This climate destroys rubber as well as things like car batteries. I only turn the shop's AC on when I'm doing something out there so it gets hot. Outdoors its 110F. with 3% humidity today >>90 in the shop.

But~ things don't rust. :-))

Re: Bandsaw tires

#10

Re: Bandsaw tires

Ken from Ontario

I chose the original type of tires that the saw came with which was Neoprene tires ,they are just like rubber tires, warm water is good enough to make them stretch, the only difference between them and Urethane tires is, I was told to use some glue under them when installing .

What I like the most is they are very thick and have a bigger cushioning effect that the thinner type but other than that ,they are all doing the same job after all.

Re: Bandsaw tires

#11

Re: Bandsaw tires

TomD

I bought some new orange ones for the INCA saw. They were easy to install, I just clamped them off at a starting point, and stretched them, then clamped them, and so forth. Maybe experience with bike tires helps. Or maybe the INCA saw is easier to load.