Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Angle Grinder Recommendations *LINK*

Posts

Angle Grinder Recommendations *LINK*

#1

Bart Goldberg

Angle Grinder Recommendations *LINK*

Bart Goldberg

I am finding a need for an angle grinder. Never used one before, but I know some folks use it for some carving? I need it to grind down some screws on the underside of my deck. I noticed that the Hitachi G12SR3 is on sale at Lowes for only $35.00. Is that a good grinder and at a good price?


http://www.lowes.com/pd/Hitachi-4-1-2-in-6-Amp-Trigger-Switch-Corded-Angle-Grinder/1240491

Re: Angle Grinder Recommendations *LINK*

#2

Re: Angle Grinder Recommendations

John K Jordan

Bart,

I don't have experience with that Hitachi but from other Hitachi tools I have I suspect it will be fine. That sounds like a Harbor Freight price - I think I will see if it is on sale here and go get one. Or two. You can't have too many side grinders! :-)

I have several 4.5" grinders, a Milwaukee, a Makita, and some Dewalts (a couple cordless). All cost far more than the $35 you mentioned. I like to keep several grinders at hand with different disks/wire brushes for welding and metal work.

They all work and handle about the same to me. The methods of changing the disks is different but all are easy enough.

JKJ

Re: Angle Grinder Recommendations *LINK*

#3

Re: Angle Grinder Recommendations

Robin Corell in Atascadero, CA

Probably a great tool for right handed people.

Re: Angle Grinder Recommendations *LINK*

#4

Re: Angle Grinder Recommendations

Mark Mandell - Gone Round In New Jersey

Years ago I bought a half dozen 4.5" grinders from HF as gifts for friends in my playgroup. $15 a piece and they're still going strong for both grinding or sanding.

Price hasn't changed either.

That said, if I've got carving or a lot of grinding to do, I reach for my DeWalt 402. The difference in vibration is notable and thus reduces hand fatigue.

All that said, since Lowe's is about walking distance from you, git'er done :D

Re: Angle Grinder Recommendations *LINK*

#5

Cut-off wheels *LINK*

Tom Dunlap

For many years I used Pferd cut-off wheels in my angle grinders. When I needed a new box i went to a local specialty supplier and was convinced that another brand was 'as good' as Pferd and a little cheaper.

Well...the other ones are OK...but NOT Pferd quality. When they're gone I'm back to Pferd.

A cut-off wheel works better than a grinding wheel. They can be used on edge to cut or on face to grind. Thin kerf too.

Which brand??? Any will work. Find the one that fits your hand. Switch configuration is important. I'll likely find one with a paddle switch like my Milwaukee's had. I like paddle better than trigger switch.


PFERD

Re: Angle Grinder Recommendations *LINK*

#6

Re: Angle Grinder Recommendations

John McGaw

I've had great service from my Milwaukee 6145. It has ground and cut more masonry and bricks than I can estimate and hasn't even needed to be blown out. Fingers crossed...

Re: Angle Grinder Recommendations *LINK*

#7

Harbor Freight

Dick Coers

They sell theirs around $15. They used to be almost indestructible. Maybe changed suppliers now, but they work well.

Re: Angle Grinder Recommendations *LINK*

#8

Re: Harbor Freight

John K Jordan

On the other hand, I know a guy who had several die on him in a short time, perhaps 20 years ago. Perhaps they changed suppliers often.

JKJ

Re: Angle Grinder Recommendations *LINK*

#9

Re: Angle Grinder Recommendations

Larry

$44.97 at Lowes by me

Re: Angle Grinder Recommendations *LINK*

#10

I borrowed one of those once....

John in NM

Couple cuts to make and my Makita was at home. Horrible. Never heard such noises from an angle grinder before, even with ear plugs (good ones) I was grinding my teeth.

I'll stick to the ~$100 price range, I use them often enough not to want to absolutely hate every second of it!

Re: Angle Grinder Recommendations *LINK*

#11

That should do...

John in NM

Though with a 6 amp motor it will be best for light duty/short duration. I used to carve a lot with mine (12 amp Makita), using a 36 or 24 grit sanding disk and holding it one handed (roughing out fairly small stuff). A smaller motor would probably do fine for that, sanding disks are cheap so you toss them when they get really dull and start bogging down the motor or burning the wood excessively.

One of those chainsaw disks or a carbide tooth wheel, I don't know, never used either.

If you're planning to grind steel instead, get a bigger motor. Anything but a thin cut off wheel will kill a small motor in short order.

Re: Angle Grinder Recommendations *LINK*

#12

Re: Angle Grinder Recommendations

TomD

If you are using stuff like lathes, table saws, and grinders, you will know most of the problems that can occur with rotating tools. That said, it is worth googling penetrating injuries from angle grinders. Truly shocking, armour up and stay out of the path.

One thing that can work really well are Dremel tools and the like. I had a friend who turned me onto their capacities when he used them to miter tubes for motorcycles. The tubes where 1/8" thick and thicker, but they cut like butter with the wheels on the Dremel. Those wheels are very thin and easily broken but they don't seem to do any harm a face shield wouldn't handle when they break. The glass strengthened ones are better. They easily cut 16d nails.

Re: Angle Grinder Recommendations *LINK*

#13

Re: Angle Grinder Recommendations

Barry Irby

Tom may be onto something here. A Dremel tool will cut screws quite nicely and is smaller and less dangerous. Wear excellent face and eye protection either way.

I have a pair of end nippers that I use to cut nails. They have the jaws sharpened on the inside so the actual cutting edge is flush with the outer surface. They will bite a nail off almost flush with the surface. And they don't create fire or tiny particles or use electrons. I would be reluctant to cut screws if the screws are hardened. Might chip the jaws. Test carefully. This is a go to tool during demo.

Re: Angle Grinder Recommendations *LINK*

#14

Re: Angle Grinder Recommendations

Mike Jurnigan in Zuni VA

For safety reasons I prefer those with the paddle switch versus the slide switch.

Re: Angle Grinder Recommendations *LINK*

#15

Re: Carving

Mark Mandell - Gone Round In New Jersey

I use a "Lancelot" (chain-link disk) for some carving [a/k/a heavy wood removal] on the DeWalt 402 which uses a paddle switch. I would never use the carver on the HF or any other constant-on grinder. Way too dangerous.

To face off protruding screw points, a small angle grinder should be fine. For cutting, however, I prefer an air-drive die grinder with 2-3" abrasive cut-off disks. The air driven tool provides an important safety feature being that if the disk binds or starts to jam in the cut it over-powers the air motor and the tool just stops before anything bad can happen. Caveat is at 10,000 rpm you want to be wearing hearing protection in addition to your face/eye shield.

Re: Angle Grinder Recommendations *LINK*

#16

Re: Angle Grinder Recommendations

john lucas

4" angle grinders are dangerous. Use 2 hands at all times and learn to read the direction they will kick if you catch the blade. Remember it's just like using the nose of the chainsaw.

I started with a Harbour freight $20 grinder and used it for many many years. I bought a second one that only lasted an hour. So I guess I was batting 50/50. I now have a Dewalt and Makita. As well as a Makita set up with the 2" discs, and an off brand 7" grinder.

The more expensive grinders have more power and are far quieter. However one feature I liked on my cheap grinder was the ability to move the guard to any position. I find using the guard as a bevel to control the depth of cut is invaluable in terms of safety. You sort of can on one of the other two grinders but I always forget which one until I get out there to use them.

My friend who uses one constantly won't use grinders that have a permanent on switch. He prefers air grinders for that reason. He said he had one get out of his hands and chase him around the shop before it pulled itself out of the wall. Of course he has a compressor that will run all day long at 90PSI. Most of us don't.

To grind down nails be careful using the cutoff wheels. They can shatter. I have a friend who lost his little finger when one exploded. My choice would be to cut them off with some sort of snips and then use a side grinding wheel to grind them flush.

Re: Angle Grinder Recommendations *LINK*

#17

Bart Goldberg

Re: Angle Grinder Recommendations

Bart Goldberg

Appreciate all the good advice. I did buy the Hitachi at my local Lowes for $34.99, but may return based on the comments about the preference for using paddle switches. I am well advised on the dangers thanks to all the good info you all provided. I will likely use my Dremel for this task after all.

Thanks Much

Bart

Re: Angle Grinder Recommendations *LINK*

#18

Re: Carving

John in NM

Sure, die grinders work great. You get used to cutting with an angle grinder after a little while too (and it uses vastly less electricity :D )

A friend of mine used a Lancelot for a bunch of carving a few years ago. He said one helpful trick was to keep the nut on the arbor a bit loose so the chain could slip a little between the two big washers that make up the tool. I never tried it myself though, the stuff I was roughing out was usually 4.25 by 3 by 2 - Waaaaay to small for anything sharp!

Re: Angle Grinder Recommendations *LINK*

#19

Re: Carving - More & Less Power

Mark Mandell - Gone Round In New Jersey

Most air tools are a big waste of power; using a 3-5 hp motor to run a tool that will do just as well with an 8 amp electric motor or an 18v battery. Air sanders come to mind when used in a home shop. The opposite is true in the industrial context where large compressors supply air to any number of tools at the same time.

IMV the die grinder is an exception as the high speed but low torque make for a safer tool. Having had a flex shaft running a cut-off wheel catch and open my thumb for inspection by the ER doc, my preference comes from experience.

Other exception (again IMV) is carving with large chisels like a 50mm #7 or 35mm #11 gouges and spoons. Having spent days swinging a 3lb mallet I can testify that the reciprocating impact pneumatic hammer (Trow & Holden) originally made for stone cutters, makes moving (removing) large amounts of wood a great deal of fun. Not for those with carpal tunnel however.

Re: Angle Grinder Recommendations *LINK*

#20

Re: Carving - More & Less Power

John in NM

I should clarify - I was talking about abrasive cut off wheels for steel or stone. Opening the thumb makes me think you were using something toothy :D I'd probably opt for the die grinder with one of those too.

Re: Angle Grinder Recommendations *LINK*

#21

Re: Carving Fingers

Mark Mandell - Gone Round In New Jersey

When it comes to body parts, a 1/16" thick cut-off wheel will do just as well as a saw blade. :(

Re: Angle Grinder Recommendations *LINK*

#22

Re: Carving Fingers

John in NM

Not an abrasive one.... even diamond wheels are exceedingly mild in an angle grinder. It is simple physics.

The danger of such wheels as this is binding in a cut (steel or rock, I've done a lot with both) causing the grinder to flip on you and smash your fingers or whatever else is in the path, or even just wrench your wrist trying to control the thing. The blades themselves are mostly harmless (to shamelessly borrow from Douglas Adams).

With about an hour's worth of experience you learn to recognize the feel of the blade beginning to bind and it is easily corrected by keeping the blade plumb in the cut.

Come to think of it, the biggest danger of abrasive wheels is probably the dust and sparks rather than any kind of accident with the grinder.

Now a carbide toothed carving disk or saw chain disk - wouldn't get near one without the accessory handle, guard, and some heavy gloves :D