Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

End grain cutting board

Posts

End grain cutting board

#1

End grain cutting board

Bruce, a MN Galoot

My DIL wants a big end grain cutting board. She's offered no dimensions, but based on our biggest side grain board it's likely to be 14" X 21". Is that length too much? I'm thinking this will end up close to 1-3/8" maybe 1-1/2" thick, so it's going to be heavy and not likely move from its appointed spot on the kitchen counter.

My question is whether 21" is too long. A smaller one I made for LOML does warp a bit but it comes right back after it dries.

Re: End grain cutting board

#2

Re: End grain cutting board

Dick Coers

My preference would be much shorter, even smaller overall. My favorite board in the kitchen is 6.5x12. I can't imagine a big slab being handy in the kitchen. But, we don't have that much counter space to give up either!

Re: End grain cutting board

#3

Re: End grain cutting board

Bruce, a MN Galoot

DIL wants to be able to carve a Thanksgiving turkey on it, hence the size.

Re: End grain cutting board

#4

Re: End grain cutting board

paul in AZ

I made one close to that size. Once. Never again.

At a thickness of about 1 3/4" it was so big and heavy that it either stayed anchored on the counter and got in the way or once put away it was rarely pulled out.

One thing I learned from a number of end grain boards is that each block has to be absolutely uniform thickness and square. I don't mean close to square ~or they will crack as the wood moves.

For a carving board used a couple of times a year I'd suggest a flat grain board. Half the weight and a whole lot quicker to make.

My most used board is around 7 or 8x11".

Re: End grain cutting board

#5

Re: End grain cutting board

William Duffield

For some jobs, I like a cutting board that is long enough to span the sink from side to side. I also have a stack of much smaller, thin boards. All of mine are flat grain, and most are hard maple. I don't think an end grain, butcher block cutting board would be strong enough when used like mine, especially if you chop on it with a cleaver.

Re: End grain cutting board

#6

Re: End grain cutting board

John McGaw

My biggest attempt at an end-grain board so far is 15"X10"X2" hard maple and weighs in at 7 pounds 9 ounces. One face is grooved, the other is smooth and there are finger grooves in the short ends to make it easier to pick up. If you haven't tried anything like this before, you should be forewarned that working with the end grain in wood like this is a real bear and getting it perfectly smooth and even is a sure path to insanity. It sure looks pretty though...

Re: End grain cutting board

#7

The best carving board

Bill Tindall, E.Tn.




What is shown is the handiest carving board I have used. What may be less obvious is that it is tilted and the rim tapers from about 3/4" to near nothing. It captures juices and parts when carving meat. It captures pieces when carving vegies like when I chop up 4 large onions for onion soup. If you have a friend who is a bowl turner making one is trivial. Otherwise it is a bit slower but worth the time. Can be end grain or not. I can provide details off line or by phone.

I use 4 kinds of "boards". We have a section of counter that is a board and it is used for baking. We have two sizes of the board shown for small and large tasks. I have a large crude board for butchering where it suffers from meat saw and cleaver. And we have several small boards to be placed on the counter for small cutting/chopping tasks.

If you pursue what you have in mind 1" is plenty.

Re: End grain cutting board

#8

Re: End grain cutting board

Bruce, a MN Galoot

I've made end grain boards before, just not one as big as she wants it. And yes, getting them smooth was a bit of a challenge. I didn't have access to a wide belt sander then, so the only thing that worked was a #3 Stanley, very sharp.

Re: End grain cutting board

#9

easier......

Bill Tindall, E.Tn.

glue a backer piece on the trailing edge and run it through the planer. Then best sand until burnished which will leave it almost nonporous.

Re: End grain cutting board

#10

Re: End grain cutting board

Barry Irby

I have made lots of them. Some as thin as 1 1/4" out of end grain walnut scraps. this was a mistake. Walnut is too porous and oil poured on the top side would drool out the bottom. And they cracked.

I leveled them by running them trough a Perfomax. Slow but worked great. I also ran some through the planer with very light cuts and finished them on the Performax. You need a back strip glued on the rear end to avoid terrible chip out.

The best one was Osage Orange. I had some that had cracked or was flawed in the tree. I cut dozens of pieces into whatever shape was needed to get rid of the defects. Squares, trapezoids, triangles, whatever. Spent a lot of time gluing the up into "strips" and then glued the strips together. The board ended up about two inches think. I really wanted to keep it, but a lady friend claimed it. One thing that added to the success was I cut the little pieces down to size and then let them sit in a conditioned space for about a year before the glue up. End grain Osage make a fabulous board. One or two coats of oil and it was like glass.

I like Bill's Carving board and may make one. On many of mine I dish out the surface so that it is about 3/8" low in the center on one side and flat on the other. The flat side is for vegies and the cupped side is for meat. It sits nicely on the four corners.

Re: End grain cutting board

#11

Re: easier......

John McGaw

Yes, you definitely want to have a strip glued to the trailing edge if you intend to run the block over the jointer or through the planer. The tearout on that standing grain is horrible to behold and no matter how light the cut it is going to happen.

Re: End grain cutting board

#12

I've never cut all the way through a turkey

Dick Coers

Does she use a machete? That may be my next Thanksgiving carving tool, not so much family arguments!

Re: End grain cutting board

#13

Re: I've never cut all the way through a turkey

Bruce, a MN Galoot

The last one she made was 22 lbs, enough for her family, her mom's family and ours, about 14 people. It's a big critter, for sure, but she wants a juice groove around the perimeter to save her floor from clean-ups.

Re: End grain cutting board

#14

Not that bad

Bill Tindall, E.Tn.

I used to put on the backer strip. Lately I don't. It get about 1/8" splintering which is then trimmed off.

Re: End grain cutting board

#15

Re: Not that bad

John McGaw

Losing even 1/8" (mine was often worse) in the boards I've made would (and did) make a difference because I took a lot of care with the grain pattern in the blocks to create a nice, almost geometrical, look. Losing a bit from one row just made things look wrong, thus the sudden revelation that putting something disposable at the edge might help. Just me, I guess.

This weekend I was cleaning up the lumber stack and the shop in general and found some of the hard maple from the last go at cutting boards and I thought about doing at least one more but then decided that the 8/4 stock might go better as table legs or something. I seldom use my own wooden boards, preferring nice big HDPE boards that can go into the dishwasher, and I've given wooden boards to every friend and family member who might want one.

Re: End grain cutting board

#16

advantages in use....

Bill Tindall, E.Tn.



I am cutting up vegies for stir fry/sautee peppers, onions and summer squash. The "well" on this style makes a place to scrape the pieces to as they are cut.

Re: End grain cutting board

#17

Re: End grain cutting board

Gary Smyth




Commercially made carving board for turkey. 12" x 20" x 3/4" maple. I liked the slanted juice trap when used for turkey and ham and roasts. Gets messy. Too large for current use with food.

Now used when finishing and dying stuff. Also fits nicely on a lazy Susan. With stubby feet underneath I can fit my fingers when lifting. Important in the day when juices were everywhere and now when I have to move the board and I don't want the finished piece sliding around.

Originally for large meat at that size the board was correct but took up a lot of counter space when there was lots going on at the same time in the kitchen -- people, multiple pots & pans, bread and rolls, salads, desserts, etc.

Talk to DIL. Thick end grain board for the stated purpose seems to me to be overkill. Even though it worked, the commercial one afterwards was unwieldy and a PIA as the spikes kept getting caught on everything when cleaning and stored. Works fine for current application though as absent food far less care needs to be taken.

Not in any way to limit you, but carving boards of excellent quality can be had for $4.50 (used) to say, $90 (new) on ebay. Most about half the high end. If you can do it for less (excluding family harmony) for the one you wish to make go for it. At least consider the time and cost you will put into it.

Re: End grain cutting board

#18

Re: advantages in use....

William Duffield

I suspect that one that was smaller dimeter and had a more eccentric rim wall height would be very useful for chopping nuts. The wall would tend to trap flying nut meat pieces, and they could be poured off the front edge.

Re: End grain cutting board

#19

(Message Deleted by Poster)


Re: End grain cutting board

#20

Jesper, Denmark

Re: Flatten like this

Jesper, Denmark

It works even better if you glue another batten at the trailing edge of the board. This avoids the chip-out of the end grain.

Re: End grain cutting board

#21

Re: End grain cutting board

Johanna

Why end grain? I have quite a few cutting boards - mostly about 12 x 16 inches - and all from hard maple. One of them was my mother's, so it is at least 70 years old! I recently sanded both sides of it as it had gotten pretty rough from all those years of use. It now looks like new.

Re: End grain cutting board

#22

Re: End grain cutting board

Bruce, a MN Galoot

End grain is marginally kinder to knives.

I changed my mind, though, and made one from edge grain maple, walnut and a little strip of mesquite for visual interest. I didn't want to take a chance on it splitting.

Re: End grain cutting board

#23

(Message Deleted by Poster)


Re: End grain cutting board

#24

Why is this Terry Q. reply showing up all the time

Dick Coers

It reappears every three days for a while, now a little longer.

Re: End grain cutting board

#25

(Message Deleted by Poster)