Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Some more bandsaw questions????

Posts

Some more bandsaw questions????

#1

Some more bandsaw questions????

Barry Irby

Are any of them less fiddly?

I have a Delta 14" saw with a riser block. I have Carter guides, a release lever, Kreg fence, etc. I have adjusted to be coplanar when the blade is on and under tension.

I just spent 45 minutes putting a blade on it. Changed one 1/2" 3 TPI blade for a similar one. Who thought it was a good idea to require two or three different Allen wrenches to adjust the guides? Every time you turn one of the screws the bearing moves. Why are there not knobs? Who put the fence adjustment bolts "under" the fence?

I spent more on "upgrades" than I did on the saw.

Is there a saw out there that makes more sense? One where you can adjust things without assembling a little tool kit? Or change the blade without dissembling the saw? Where you can change from slicing veneer or resawing to cutting a bowl blank in a few minutes? Apparently I need two bandsaws.

Re: Some more bandsaw questions????

#2

Re: Some more bandsaw questions????

Bill Tindall, E.Tn.

Find a used ancient Delta 20"

Re: Some more bandsaw questions????

#3

Re: Some more bandsaw questions????

Doug Reynolds

On my newer Jet 14" bandsaw I replaced the Allen head screws with "thumb" screws.

Re: Some more bandsaw questions????

#4

A tip

Bill Tindall, E.Tn.

put a disk magnet on the saw and attach the appropriate sized Alan wrench to it to be at hand as needed.

Re: Some more bandsaw questions????

#5

Re: A tip

Barry Irby

Thanks, good idea. Actually I used to keep the two Allen wrenches on the stand with some blue tape, signifying they were the ones. They evaporated. There is a near by shelf. I drilled holes in the edge of the shelf and inserted them. I think they are inconspicuous enough to keep them from evaporating again. My son not knowing where they are cuts the evaporation rate.

And I will start looking for a 20" Delta. There is a used tool dealer in the area. Are parts available if I need them?

Re: Some more bandsaw questions????

#6

Re: Some more bandsaw questions????

Barry Irby

Good idea. I have done similar on other tools. I will try to find some.

I just hate stupid stuff like this. If the need is that obvious to me, surely the manufacturer knew and could have anticipated the need.

Re: Some more bandsaw questions????

#7

Re: Some more bandsaw questions????

John in NM

Personally, I've always preferred the kind of saw I described in that other thread, and the reason is they are wonderfully stiff, and probably they were made more carefully.

On mine, blade changes take about 5 minutes, if that. Rarely have to adjust tracking or guides if its the same kind of blade. Mine is new enough (last of the real Generals) to have come with bearing guides, but it would do just fine with those old style block guides. A saw that tracks well by itself doesn't need fussy guides IMHO.

So I would look for an old PM 141 or 143. The 141 is a lot cheaper, not having all the speeds they set up for metal shops. Still set you back $800-$1k though, and you still might have to do some work on it.

Re: Some more bandsaw questions????

#8

Re: Some more bandsaw questions????

John K Jordan

Barry, you are describing my Delta saw to a "T", except I tried and ditched the Carter guides in favor of cool blocks. I got a lot of use from that saw and still have it, but I far prefer the 18" Rikon I've been using for a number of years now. It too needs several allen wrenches to adjust the bearing guides. I put some allen wrenches on long handles to make them easier to use, especially under the table.

I also wish for micro-adjusters on all guides. It takes me about 10 minutes to change a blade and adjust the guides. I generally use 1/2" 3-tpi blades on this saw too.

JKJ

Re: Some more bandsaw questions????

#9

Re: A tip

ben d.

Either of these may be worth a look.

https://www.govdeals.com/index.cfm?fa=Main.Item&itemid=778&acctid=397

https://www.govdeals.com/index.cfm?fa=Main.Item&itemid=169&acctid=7868

ben d.

Re: Some more bandsaw questions????

#10

Re: Some more bandsaw questions????

Johanna

In spite of the fact that I have had switch problems, I really do like my Steel City bandsaw. The guides are easy to use - all have knurled knobs and simple lock mechanisms. Changing the blade takes about 15 minutes, most of it spent in carefully adjusting the guides so they are as close as possible without touching.