Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

LED diy shop lights

Posts

LED diy shop lights

#1

LED diy shop lights

Ray - Middletown, IN

Found some strip LED's and decided to do a little prototyping.



Made a plywood box 48 x 6 x 3 and mounted the strips to a piece of 1/4 ply.



None to clear close up of the strips. The yellow squares are the LED's



Went to the borg and picked up a sheet of the drop in light panels and cut it into strips and slid it over the LED's.



Need to get it up next to the flourescents but I think it is going to work.

Cost:

LED strip $3.25

Power supply $4.50

Cover panel $2.50

Plywood $2.50

I had enough ply to do the prototype but using Luan and such I think the cost will be manageable.

Ray

Re: LED diy shop lights

#2

Re: LED diy shop lights

John C Lucas

There is an excellent you tube video on making your own photography lights using the strip lights. Wish i had kept the link. He made a light about 2' x 3'.

Re: LED diy shop lights

#3

Re: LED diy shop lights

John K Jordan

Nice! I love those strip lights. I got some and a dimmer for my display case. They should be good in the shop.

JKJ

Re: LED diy shop lights

#4

Re: LED diy shop lights

Gary Smyth

It may be helpful to use the chart to get a rough comparison of the output derived from your solution. You may also wish to check your LED label for the color temperature of the light produced. (Look for 5500 degrees Kelvin to approximate daylight/sunlight appearance The higher the listed temp K the light take on a bluer cast. Lower, the shade will appear to get yellower. This info may assist you when assessing stain/paint color viewing.

Watts (energy usage) Lumens (light output)

25 200

35 325

40 450

60 800

75 1100

100 1600

125 2000

150 2600

You might also want to consider placing crinkled aluminum foil, or better, chrome Mylar sheet behind the light. Because LED's give off little in the way of heat, the foil does three things. It is in little danger of heat buildup and fire, by "bouncing" the light it will almost eliminate shadows, and it can make the light a bit brighter as it can reflect "lost" light absorbed by the light fixture itself. You may also find that when placed overhead the plastic light cover will not be necessary -- with, it will look neater however.

Re: LED diy shop lights

#5

Kneale Brownson

Re: LED diy shop lights

Kneale Brownson

How about using old shop lights where the ballasts have failed?

Re: LED diy shop lights

#6

Re: LED diy shop lights

John McGaw

Nice idea but I can't help but think that the light output will be very low with single-density LED strips. I use high-output double-density LED strips for various tasks and they are still not nearly as bright as an equal-length fluorescent tube (using less power, obviously). The light I put into my drop-front desk has two strips of double-density LEDs the full width and the light is far from blindingly bright even at a distance of one foot. At ceiling height it would be pretty dim light to work by.

Re: LED diy shop lights

#7

$3.25?

GolfSteve in Calgary

$3.25 for the LED strip and $4.50 for the power supply? When are you living - 1930?

I made a shop light using Lee Valley's 14 Watt/metre (60 LED/metre) strip LEDs. The result is much brighter than a twin T8-tube fluorescent fixture.

Here's a link to what I built:

http://www.woodcentral.com/woodworking/forum/archives.pl?pro=search;pmd=sread;srchid=1324Wo5B63g6MndMf5c1466115368;spage=1;sanc=474277;sbid=1001;md=read;id=474277#m_474277

But it cost me about $300 for the LEDs, aluminum channels, and power supply!!!

It turned out to be too bright, so disconnected the shorter middle strip, leaving about 4 meters of functional LED strip. It's still very bright.