Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

WC Weekend Accomplishments....

Posts

WC Weekend Accomplishments....

#1

WC Weekend Accomplishments....

Dennis E Peacock

13 June 2016

Good Morning Everyone,

I'm getting a head start on this as I have an appt early tomorrow morning. I spent most of the weekend putting in drip and micro-irrigation in the new flower beds around the house for the LOML. The rest of the time was celebrating my birthday with my family. My customer brought me another chair to model good parts from for the chair project I'm still in the middle of. Thanks for woodworkers that live near by, I was able to get 3 pieces of mahogany to make the new pieces from. My hope is that I don't mess up turning these as these are the only pieces I have onhand at this point in the game. So here's to hoping for a successful remake of the parts once more.

That's it for me, so what did YOU do this past weekend?

Best of weeks to you all.

Dennis Peacock

Re: WC Weekend Accomplishments....

#2

Progress & Shavings

Mark Mandell - Gone Round In New Jersey

An active w-e here.

With the drop-dead gorgeous weather, it was quite impossible to be inside. Saturday was the day to prune and trim all the landscaping that I've not touched for several years. Cuttings amounted to only half a trailer load so, compound shear and chain saw in hand, I took on the damn Russian Olive infesting and slowly choking our "back 40". Full load tied down, it was on to the township stump dump for the first of my freebe deposits for the year.

Sunday it was time to unwrap and check my PPB wood stack. Temps had gotten to 125° several times so, while maybe not enough to kill the eggs, I wanted to see if anything was happening. Unwrapped and found 15-20 little buggers dead on the surface of some of the boards. This is encouraging, so rewraped and sealed the stack. That done, I pulled Stubby out of its garage niche to finish Memsahib's sugar maple salad bowl that's been sitting on a shelf in the garage for the best part of 3 years. Wow, that stuff was like cutting concrete. My bowl gouge technique is so rusty I had to pull out the Cobra hollower and fit it with Hunter cutters to get a decent cut. After filling some cracks in the bowl, I decided to take on a few bone dry Ambrosia Maple log sections I had sitting in the garage. Managed to get two nice 12" cylinders about 2' long turned round for jars. One had a small crack and a rotten knot so took it down to the basement and filled it with epoxy; should make an interesting graphic when finish turned.

Monday, got up looking for the Aleve!! Jeez, talk about rode hard and put away wet . . .

Re: WC Weekend Accomplishments....

#3

Re: WC Weekend Accomplishments....

paul in AZ

Spent a delightful day with the young gal who wants to learn to build things.

This time she needed a two level plant bench for her apartment balcony. She came up with the sketch and dimensions; I got some cypress and we went at it. As before, I didn't actually do anything [except run the table saw] but talked her through each step. She cut some basic joints by hand and bandsaw, assembled everything -including dowel plugging all screw holes, and finish sanded everything. She is a quick learner.

This took a good part of the day including going out for lunch and a half hour or so correcting a measuring error.

Fun.

Re: WC Weekend Accomplishments....

#4

i built a 30' long bridge out to my float dock.

Keith Newton

That was after tearing out the old 20' long one, which was still pretty good, being only ten years old. It was just too darned steep after I built the new fixed dock about 3' higher than the one it replaced.

But the best part about adding another 10', was that By building it trapezoidal I angled it downstream about 7.5* which put the floating dock out under the shade of a little cypress grove, beside the deeper channel. This will make it a lot more pleasant to go out on during the heat of the day. It also improved the view both up and downstream, not to mention improved the fishing.

Re: WC Weekend Accomplishments....

#5

Re: WC Weekend Accomplishments....

John Foster


Built from scratch. Maiden voyage on Friday.

Re: WC Weekend Accomplishments....

#6

Terrific job

Gary Smyth

Congrats on the build. Curious though, Did you do a center of gravity consideration? Not knowing the weight distribution/dimensions/contents you may get some squirrely behavior at speed. Be aware on your first runs.

Re: WC Weekend Accomplishments....

#7

Re: Terrific job

John Foster

On a test run on a very windy day it seemed to handle nicely. We plan on being conservative on freeway ramps and corners in general. I don't know the exact vertical centre of gravity. The water tank, propane tank, battery and porta-toilet are at truck bed level, the fridge, furnace and water heater are on the wing at box side level. We did put LT rated tires on that we can inflate more if needed and Firestone air bags on the rear axle.

Thanks for the compliment

Re: WC Weekend Accomplishments....

#8

Re: WC Weekend Accomplishments....

William Duffield

Nice job, and it looks comfortable. I'm beyond the age where I enjoy tent camping, so something like that is very tempting. I notice you have it securely tied down to the pickup.

However, it reminds me of an almost horror story that happened to my wife. She was stopped at a traffic light. A stolen pickup with a camper on the back was coming in the opposite direction, with police in pursuit. The thief hung a hard left in front of her, and the camper and box separated from the truck frame and slid, while disintegrating, directly towards her. Luckily no one was in line behind her, so she put her car in reverse and quickly backed up about 20 feet. The camper top stopped right where her car had been.

Re: WC Weekend Accomplishments....

#9

Re: WC Weekend Accomplishments....

Jerry Gibbs

Finished 15 bird house kits. Makes a difference when the houses are to assembled by kids using only a hammer while supervised by a non-woodworker. Have to think like a pre-fab engineer.