Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Raised "L" TS fence

Posts

Raised "L" TS fence

#1

Raised "L" TS fence

Jerry Gibbs

I am making 15 bird houses to be assembled by camp kids with no experienced adult help. I want all the parts to be interchangible. There are a total of 30 front and back pieces, as shown in the mdf patterns. I found the raised "L" fence to work well for production. I know there are other methods, these are bird houses, but this went well. I also like the fence for long angled cuts. I just tape a straight edge to the line and cut.

Re: Raised "L" TS fence

#2

Re: Raised "L" TS fence

Tony - Memphis

Nice! I saw that trick on Roughcut and have been wanting to try it. Just haven't has a need yet. Looks like it works great. For some reason, it makes me a little uncomfortable, but logic says it is safe.

The young ones will surely enjoy their house projects! Maybe you will inspire some new woodworkers?!?

Tony

Re: Raised "L" TS fence

#3

Re: Raised "L" TS fence

Ray Newman

Fine Woodworking video about the "L" fence --

www.finewoodworking.com/how-to/video/versatile-tablesaw-l-fence.aspx

Re: Raised "L" TS fence

#4

Re: Raised "L" TS fence

ChuckInND

At first I thought that it was similar to the Unfenced that can be positioned similarly. Now I see the raised position of it and thinking that it's similar to using a template with a router, but maybe better for this situation. Good idea.

Re: Raised "L" TS fence

#5

Re: Raised "L" TS fence

Keith Newton

Jerry, That is a nice trick. The only concern for me, is that the waste would continue to accumulate under the fence, then as you cut those low angle wedges, which would be opposing direction, there is a chance of them jamming against the actual fence, then forcing a piece onto the back of the blade. Of course the overhead part of the L would provide a level of safety from it climbing the back of the blade. How often do you clean out the parts?

Re: Raised "L" TS fence

#6

Offcuts jamming --> kickback?

Henry W

This looks great for irregular pieces. Absolutely.

Do you somehow clear the offcuts? Aren't you concerned they will (or could) 'pile up' under that fence, jam into blade, and become projectile material (cause kickback)? For longer pieces (longer than the normal fence to blade separation, even the act of clearing them might push them into pinching between fence and blade (kickback position).

I'm not certain about this, but want to be sure that you are (both certain and safe).

Henry

Re: Raised "L" TS fence

#7

Re: Offcuts jamming

Mark Mandell - Gone Round In New Jersey

will occur if the operator leaves his smarts outside the shop door. The "under fence" area needs to be cleared after several cuts. Simply turn off the saw and shove a board through between the main fence and the stopped blade. The one I made is about 4" wide as my cut-offs were never wider than an inch or so. Heavier stock gets cut off on the band saw first. I also did not depend on just a glue joint and reinforced the "T" with 4 screws.

I've used the "L" fence on a number of pieces and it works as a very safe alternative to a taper jig, especially where you're tapering thicker leg stock.

Small Tips:

Put "slick strip" tape or a piece of HDPE on the working edge of the fence so the guide piece slides smoothly.

Double-faced carpet tape is essential unless you're going to fix your guide piece with screws. I seem to remember the mag article using sticky-back sandpaper. I would never depend on mere friction to hold the guide piece in position.

Re: Raised "L" TS fence

#8

Re: Offcuts jamming, good points guys


Re: Raised "L" TS fence

#9

Kneale Brownson

Video doesn't play, just the advertisement


Re: Raised "L" TS fence

#10

Re: Video doesn't play, just the advertisement

Ray Newman

Works on my computer. It automatically loads and plays after the sponsor's message/ad.