Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Multi tool for mortises

Posts

Multi tool for mortises

#1

Multi tool for mortises

Forrest Addy

Long time no post.

The subject line says it all. Anyone hear of using a multi-tool to buzz the outline of a mortise? Think the Rockwell RK5121, DeWalt DWE315, Porter Cable PCE606, etc. Then run several cross grain kerf cuts, break out the flakes, and (if necessary) pare to refine/size the feature.

I bet with a little practice and maybe a guide block, to aid square starts, a wood-butcher could efficiently cut clean mortises with fewer steps. Maybe use a jig with sized openings for multiple parts. Beats a heavy immobile chisel mortise and the hard to sharpen hollow chiseled. Hm, come to think of it, an oscillating saw IS portable in case you need to M&T off a ladder or scaffolding. Maybe carpenter up a plant sconce in the Spruce Goose

I'm gonna try it tomorrow.

Re: Multi tool for mortises

#2

Re: Multi tool for mortises

Keith Newton

Yes, I've done that plenty of times, usually on larger mortises. It helps to start the cut with a chisel, so there is a little corner / step to help index the tool on the beginning of the cut. Usually after having used a plunge router for most of the work, and this just for squaring the corners.

On smaller mortises, I'll use my Automach power carver with a special straight bit that I ground from a 1/4"x 1/4" x2" metal lathe tip, to get a tang on one to fit the chuck, and bevel on the other.

Re: Multi tool for mortises

#3

Ellis Walentine

Good question, Forrest

Ellis Walentine

I can definitely see how this would be possible, though I'm skeptical as to whether it will be a net time savings over a plunge router or skilled chisel work. Please report back and let us know how it works out for you and where you think it makes the most sense.

Ellis

Re: Multi tool for mortises

#4

Re: Multi tool for mortises

Barry Irby

Give it a try and let us know. I have several Multitools. Bosch, one corded and one battery powered. I am a little skeptical of cutting a deep mortise. Perhaps it woudl work if you did it in stages. Unless its huge, you are going to run into the limit of the length of the cutter. My other concern is where will the saw dust go if it cannot escape the cut?

I like the multitool and find more uses for it constantly.

Re: Multi tool for mortises

#5

You must be better with that thing than I am

Dick Coers

Maybe I'd try it on a western red cedar garden gate, but not on much else.

Re: Multi tool for mortises

#6

Re: Unintentional Obfuscation?

William Duffield

If you'd just said "Fein Multimaster" I wouldn't have had to ask Google to look it up for me and wade through a bunch of alphabet soup ads for knock-offs to figure out that you weren't talking about a Leatherman. :D

It's good to see you here again, Forrest.

Re: Multi tool for mortises

#7

Re: Unintentional Obfuscation?

Forrest Addy

I was referring to and oscillating saw. I looked on eBay for about ten seconds to find examples and the list I posted was it. Chalk it up to sloppy research.

Re: Multi tool for mortises

#8

Re: Multi tool for mortises

Forrest Addy

Length I dunno, but the sqaws I have will elet me plunge 1 1/2" or so. Sawdust? You'll probably have to peck like you extract a drill periodically to clear the swarf. An experiment will sow the way.

Hell, don't you guys wait for me. I'm not claiming turf. If you're curious and have the wherewithal handy try cutting a couple mortises with an oscillating saw. Don't forget to kerf cut the waste cross-grain so you can break out the flakes. Hard to pry out an intact block without buggering up the mortise walls.

Chances are an oscillating saw mortise won't go perfectly the first time. Murphy's Law sees to that. But even at its greatest refinement you'd probably have to pare a little.

Re: Multi tool for mortises

#9

Re: You must be better with that thing than I am

Forrest Addy

I'm better at everything than everybody except saying "no" to chocolate brownies but I'm working on that.

Re: Multi tool for mortises

#10

You mean this? *LINK*

Christopher Fitch Memphis

You could use the Festool plunge base I'd imagine similar to what's shown in the video.

And you can use that on a Fein Supercut or even a Multimaster (some models require slight modification to use it).


https://youtu.be/2yBQnhaZA1w?t=4m14s