Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

finishing several pieces at a time

Posts

finishing several pieces at a time

#1

finishing several pieces at a time

mike vanpelt

Received a nice commission to build two Morris chairs, Mission Style Queen size bed, Mission style couch, and Mission Clock. I have the chairs built. sanded, and ready to apply finish. Do you think I would get a "better Match" if I waited and finished all the pieces at once rather than finishing them as they are built?

Will it make any difference?

thanks

Mike

Re: finishing several pieces at a time

#2

I assume you are putting on some kind of color

Dick Coers

As long as the color mix is all the same batch, you use the same sanding schedule, and you apply the color with the same method. I see no issue with doing each separately. Now if you use a glaze, or gel stain to leave some color on the surface, a batch method may be better. It would help if you describe your methods and materials.

Re: finishing several pieces at a time

#3

Stickley finish

mike van pelt

I am sanding to 150 grit with my Festool Ro150 6" sander then lightly wetting edown the quarter-sawn white 0ak with water to raise the grain. .

Then sanding again to 150 grit via sander then sanding to 180 grit by hand. I apply a water based Van Dyke Brown dye.

Then a coat of glazing stain rubbed in with a coarse cloth.

Next day then I wipe down with clean cloth and spray three coats of water-based General Top Coat sanding betwen coats and when all finished I buff down with purple pad and dark wax.

thanks

Mike

Re: finishing several pieces at a time

#4

Re: Stickley finish

Keith Newton

I think I would skip this, and use 180 on the sander. I think you will end up with swirls, with only hand sanding after 150, but maybe you like hand sanding better than I do.

Re: finishing several pieces at a time

#5

Re: Stickley finish

Dick Coers

I would mix up enough dye to do the whole job at once, unless you use something very accurate like a digital scale to measure the ingredients. After that, I suppose the wood will have enough variation, there will be slightly different colors anyway.

Re: finishing several pieces at a time

#6

Curious

John in NM

I learned to use steel wool or something like it to "cut" the raised grain off, and then not sand again afterwards. As with any technique learned from another and not experimented with, it may be incorrect - just wondering how others learned to raise the grain.

Grain raising is something I never used to do until I used a few water based finishes - then it clearly became a necessary step for some woods. Honestly, I tend to avoid water based finish as a result.

I do raise the grain after any rasp work. Amazing how even after sanding all the rasp marks out, they can pop right back up given a little water. In that case I do sand afterwards, because it's really a different kind of grain raising - taking out dents made by the rasp teeth more so than fibers folded over into the wood pores by sanding.

Re: finishing several pieces at a time

#7

Re: Several Ways

Mark Mandell - Gone Round In New Jersey

a. Using a sharpened card scraper cut the "hair" off. By actually cutting the fibers you can get brighter grain that some insist is de rigueur. Hard to do on profiled surfaces unless you can make your own card profiles.

b. After raising and before applying an y finish (especially waterbornes) wet the surface with a spit-coat of dewaxed shellac mixed very thin (1/2 lb). This dries very fast and stiffens the raised grain which can then be sanded off with fresh, sharp sandpaper moving with the grain direction. With open pored woods like oak, ash, or walnut, I do this twice before going forward with finishing.

In fact, the shellac application can help you with the card scraper as well.

Re: finishing several pieces at a time

#8

ps

Mark Mandell - Gone Round In New Jersey

Never, ever, use steel wool on wood that will be finished with waterborne/based finishes. Small particles of the wool will be embedded in the grain and will then rust and produce red-brown spots in the finish film.

Re: finishing several pieces at a time

#9

Oil only for me....

John in NM

But thank you for the heads up none the less :D

I've seen paper backed maple veneer do that too, we never did figure out why. Bits of veneer knife perhaps?