Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Micrologging, milling, and stickering *LINK*

Posts

Micrologging, milling, and stickering *LINK*

#1

Micrologging, milling, and stickering *LINK*

Grant in Iowa

I posted this a week or so ago, but I have now added some photos of stickering and stacking lumber to the album. it now includes bucking, moving logs with a home made log arch, loading them on the trailer, milling, and now stickering.

One aspect left is the process of bringing lumber indoors after it has air dried. I have a stack of lumber ready for just that, I just need to get the work done and take photos of skip planing, sorting, and placing it in the racks for use.

The link takes you to Flickr, an online photo host. You can click on each photo for a high resolution version. Each photo has my notes below it. Check it out!

If anyone has questions, I am happy to share the little bit that I know. I am also happy to hear constructive criticism about how to make the presentation better. I know there are a few here who have a great deal of experience that could offer more information.

Regards,

Grant in Iowa


micrologging

Re: Micrologging, milling, and stickering *LINK*

#2

Re: Micrologging, milling, and stickering

Keith Newton

Looks like you have it going on there Grant.

I had thought about building myself a log arch, but so far I haven't really needed one. Most of my logs are urban, where I can get close enough with the trailer to just go straight from the ground onto the trailer. That got to be a whole lot easier when I built the arch boom on the back of my car hauler trailer. With snatch blocks, I can lift the log from the ground with the winch cable going up to it, then down to the log.

The only thing I might suggest, since I'm sure you are cutting this lumber for your own use, rather than for the market, is the edging. If there is an electric power source there close to the mill. Rather than setting the lumber aside to be straight edged later, you could transfer each as they come off the mill, over to a couple of sawhorses where you are standing. Then using a circular saw to just follow the edge of the bark, or on over to the sapwood / heartwood transition if you don't plan on using the sapwood, which is what I do. It doesn't make for as pretty a stack, but your yield will be higher. Plus, you will have some nice curved chair back-leg material from down near the butt-flair.

I would like to have seen the stack started higher off the slab too. Even though that slab may look dry, it will be absorbing moisture from all sides whenever it rains. Then when it evaporates under the stack, it will, if not be picked up by the lumber above, it may use a good portion of that air capacity to absorb a quantity of moisture, in the limited space. When you unstack later, you might try to remember to have a meter on hand, to check the MC throughout the stack, to see if it is higher down there. I'm also hoping that the 5/8" sticker thickness doesn't cause a problem toward the inside of the stack.

Re: Micrologging, milling, and stickering *LINK*

#3

Re: Micrologging, milling, and stickering

Grant in Iowa

Hi Keith,

When I decided to buy/ rebuild the log arch, I had experienced missing a couple walnut logs because of their location. I began planning to build one, but before I had bought anything I found this one on craigslist. It was rickety and poorly welded, so I beefed it up and added several new pieces of steel to make it mine.

The stack of lumber shown is the first time I have had three stacks drying at the same time, so I was low on blocking to make it higher off of the ground. As far as the sticker dimension, I have been using them like that for about 8 years now. The late Martin Plotz also used 5/8" stickers with great success in his milling business. I originally found that wider stickers are more prone to sticker stain in this neck of the woods. I will take your advice and measure the MC of a stack I am about to bring in the shop in several places and report back. One mitigating factor for my situation is that my home and shop are located on the highest ridge line in the county, and as such it is quite windy on most days. I suspect that may add to my success with smaller stickers.

I like your idea of keeping a circular saw handy during milling. I may just implement that one. My sawyer works fast enough, and keeps me busy enough that he would probably still get to it before I could pick up a saw, however. Not shown in the photos, but he keeps and eye on the height of the cant he is workign on and the width of the boards needing edging. occasionally, usually as he turns the cant 180 degrees to guard against bowing, he'll unclamp the cant and add a board needing edged vertically between the clamp and cant. It then gets cut on the next pass, while simultaneously cutting a board from the cant.

Thanks for the kind words and recommendations. There's always room for improvement in anything we do.

Regards,

Grant in Iowa

Re: Micrologging, milling, and stickering *LINK*

#4

Re: Micrologging, milling, and stickering

Keith Newton

Hey Grant, I couldn't see what you had done with the winch on the arch. Have you got any other pics showing that?

Also curious what your pay your sawyer?

Re: Micrologging, milling, and stickering *LINK*

#5

Re: Micrologging, milling, and stickering

Grant in Iowa

Keith,

The winch was admittedly a splurge. We could have gotten a farm store cheapie, but I have had them fail before, we decided to buy one more that would stand a chance of outliving me. We also wanted 3/8" cable that would provide some overkill, as well as be more kink free. So, I bought a Warn Zeon 10 with the multi-mount option. The multi-mount is a carrier, which is designed to mate in to a Category III hitch receiver. This arrangement allows me a great deal of flexibility, as well as being able to remove and store the winch when not needed.

So the trailer has a receiver mounted to the frame at the front of the trailer, and the winch slides in to that. The winch slides in, a pin is put in place, and the power hooked up to the on board trailer battery. The battery has more than enough juice to run the winch for a load of logs. I can actually also use the winch in the same location to unload the logs. I will have to provide photos to clarify this arrangement a bit perhaps. Basically, the winch cable end hooks to a stake pocket at the rear of the trailer on one side, runs forward and around the front of a log, and is routed to back to the rear of the trailer on the opposite side, through a snatch block and then to the winch. Tightening the winch forces the log off the trailer. I usually find, however, that I can tie the log to a fence post or second vehicle to remove logs easier, so I have not used the method much.

I also mounted a receiver on the front of my truck, added a second battery in the truck factory location made for that, and wired it all up with a battery isolator. The winch can be moved between locations, although at 120 lbs, it is best to have two people to move it around. I also use a locking pin when leaving the winch on the trailer to guard against theft. I tend to store the winch when not in use.

My sawyer is not a full time sawyer, but mills nearly every weekend and some evenings here and there in summer. I have known him for a dozen years. He generally charges people 30 cents per board foot for milling, but he expects they will off bear the lumber and slabs at that rate. He does offer me a bit of a discount from that rate that I have promised not to disclose. As I have said he likes that I bring help and know my role while the milling is happening. He also likes the fact that I can deliver clean logs that haven't been dragged, thanks to the log arch.

He is also willing to work by the hour, but I don't know the rate for that service. He usually works by the hour for odd custom jobs or jobs with very small logs. he had a guy drop off a bunch of cherry logs that were 12" max recently. I think that guy got the hourly rate.

I think he gets $1.50 per mile one way for a travel fee for plus the normal rate for mobile jobs. I haven't used that option in about 8 years.

Here in Iowa, I have heard two sawyers tell me that milling is not taxed if it is done on a farm and the logs came from a farm. They call it a farm product if it meets that test. Tax laws vary I suppose, but I haven't paid sales tax. I know Iowa is very pro farmer with the laws.

Keith, you mention a swinging arch arrangement on your trailer to load logs. I am intrigued and would like to see a photo or drawing of how it works. I actually changed from a typical car trailer to my tilt bed car trailer for easier log loading and unloading. It kind of sounds like you might have solved the problem with an arch.

Truth be known, I too will often go straight to the trailer with a log when possible. I will back the trailer up next to the log so just the front of the log will roll on to the tilted trailer. Then, I get behind the log with my tractor and push it aboard. Even though the bucket lift capacity is about 600 lbs, this is usually enough with smaller logs, and the tractor can easily slide a log lengthwise on the wooden deck of the trailer. I do try to avoid hauling the log arch and tractor to a location, unless the job requires it.

I have found that most semi-urban land owners will give you a log if you can move it without tearing up their property. That has been my niche, and I have not paid for a log to date. I do usually offer to clean things up, which is indeed work. I will refer you to my photo and say that I could use the exercise anyway :)

Thanks for the conversation.

Grant in Iowa

Re: Micrologging, milling, and stickering *LINK*

#6

Re: Micrologging, milling, and stickering

Keith Newton

Oh, I see now, the winch I was asking about was the one on the front of the log arch. I guess it is just a boat trailer winch, running back through a snatchblock. As I look at that, it occurred to me that one might could put it on top of the arch, would eliminate the need for going through the block.

I mounted my trailer winch forward of the bed, on the triangle, with the cable running under the front rail. I would worry about having to hit the brakes hard, with it back there in front of the logs.

One thing I do to get the chain or cable under a log, is to cut a limb at a long wedge or diagonal. THen shove the point under the log near the middle, and roll it up the ramp above the wedge, onto the level. This sets it up like a seesaw, with one end on the ground, and the other up in the air. If the wedge limb is large enough, the high end may be high enough to back the trailer under, then start winching. Tossing limb rollers under the trailing end, keeps it up out of the dirt.

I'll send you some pics of my trailer later.

Re: Micrologging, milling, and stickering *LINK*

#7

Re: Micrologging, milling, and stickering

Grant in Iowa

Keith,

On the log arch, the winch is a two speed hand winch of similar design to those used on boats. It is a heavy duty one with a 3200 lb capacity. It too can be removed from the log arch and stored inside.

I emulated the design of the Log-Rite tractor arch in my version and routing of the cable. I will say that the location of the winch keeps the winch operator out of the danger zone when lifting a log. I do need something to prevent injury should the cable break during a lift, however. Maybe a loop of steel that the cable passes through or similar.

We had given thought about doing what you described with the winch atop the main beam and an idler at the rear of the arch, but opted for the *apparently* well tested log-rite method of routing and lifting the log.

I will say that the long distance the cable travels has two additional benefits besides being a safer location:

1. more distance reduces the angle of the cable in relation to the winch. This makes for smoother winding and less tendency for the cable to pile up on one side. This is an issue because there are multiple attachment points for the snatch block to be suspended (the D-rings in my photos). To be fair, we usually use the two inside rings, as this makes the cranking easier because of the doubling effect.

2. Less cable on the spool equals easier cranking, just like with any winch. I'd shorten the cable, but I occasionally use the winch for other things.

I will add that we try to improve anything we find to be less than ideal after each use of the custom equipment. We discovered that when using the log tongs to lift a smaller log, the snatch block mounting point isn't high enough. So, we plan to add a snatch block attachment point slightly behind the cross-bar/ arch of the log arch. We'll set it up such that the cable just sneaks beneath the cross member, goes through a snatch block then to the tongs. Doing this will gain us about 6" of lift.

In support of this idea, I have already acquired a 20" receiver sleeve to be integrated in to the back end of the main beam. This will allow me the ability to add an attachment point for this snatch block, yet be able to remove it to put whatever else there that is conceived. Always thinkin'.

Grant in Iowa

Re: Micrologging, milling, and stickering *LINK*

#8

Re: Micrologging, milling, and stickering

John K Jordan

Nice job, good solution!

I've had a Woodmizer behind the barn for over 10 years now but I wimp out when it comes to moving logs - I haul the tractor to the logs on a trailer, load the logs onto the trailer with the tractor, haul the logs home and unload, then go back after the tractor. :-) If I'm sawing a downed tree on my own property I just drag it to the sawmill with a big skidding tong on a chain (I welded grab hooks to my tractor bucket.)

If I moved a lot of logs on someone else's property I'd probably build some kind of arch.

When I saw it's usually by myself so I put forks on the tractor and stack the boards directly on the forks as I pull them off the sawmill.

I like to use red cedar stickers instead of hardwood or pine since they dry so fast and seem to draw moisture away from the boards instead of trapping moisture and inviting fungal stain. Cedar stickers don't degrade over time either. But I have used other woods without problem. I always use 1" stickers. If the stack is wide I try to make a "chimney" slot near the center to help with circulation.

Plastic over concrete might make a moisture barrier, but I would still want plenty of air circulation. My normal stack is two rows of 3 cinder blocks, long 3x3 or 4x4s down each row, 3x3s running crossways at each sticker location, then a 1x1 sticker centered on top of each 3x3.

I need to get back to sawing myself. I have a big stack of ERC logs, some elm, poplar, oak, walnut, pine and osage orange. Osage is my favorite wood for garden stakes. :-) My problem is sawing is addictive and once I get started I usually end up with more boards than I can use. I still have a bunch of cherry from six years ago I'll probably use for siding on a new shed. Ack!

JKJ