Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Another thought on Cherry/sapwood

Posts

Another thought on Cherry/sapwood

#1

Another thought on Cherry/sapwood

Barry Irby

I posted below asking for thoughts on the sapwood in cherry.

While struggling with this it occurred to me I have a lot of offcuts that are three feet long. The head board of the bed is simple and has a convex rounded panel.

I could cut the stripped pieces into wedges/segments of the circle and glue them up with lots of contrasting stripes. I am visualizing a sort of sunburst. At least this would make it look like the stripes were a feature rather than an unfortunate use of wood. Any thoughts?

Re: Another thought on Cherry/sapwood

#2

Re: Another thought on Cherry/sapwood

Hank Knight

I think that sounds nice. I'd be careful, though. Too much contrasting striping would make it look too "busy" for my taste.

Re: Another thought on Cherry/sapwood

#3

Re: Another thought on Cherry/sapwood

Dick Coers

You may have an issue with wood movement if you stack the boards with too many of them vertically. That's a lot of boards expanding and will want to move differently than the lower rail.

Re: Another thought on Cherry/sapwood

#4

Re: Another thought on Cherry/sapwood

Jesse Cloud

Here's a solution to both problems above...

Resaw the pieces to less than 1/8, and keep them in sequence (draw a triangle on the side before sawing). Use them as veneer on ply or mdf. That thin, they won't move much and if left in sequence there will be a pleasing pattern from one board to the next.

Re: Another thought on Cherry/sapwood

#5

Re: Another thought on Cherry/sapwood


Re: Another thought on Cherry/sapwood

#6

Re: Another thought on Cherry/sapwood

Barry Irby

I thought about the movement. I was thinking about making a frame headboard and mounting the panel on that with allowances for movements. Had not thought about the veneer options. Thanks

Re: Another thought on Cherry/sapwood

#7

Re: Another thought on Cherry/sapwood

don stephan

Let's say you make a half circle starburst using solid wood wedges, and want to allow 1/8" per foot seasonal movement. That is a figure I see in a lot of literature and I think a ballpark number in Hoadley's first book. Compare the distance at the circumference of the half circle with the "distance" at the center and multiply each by 1/8".

Veneer less than 1/8" thick on a stable substrate would avoid the problem.

Re: Another thought on Cherry/sapwood

#8

Re: Another thought on Cherry/sapwood

William Duffield

The sunburst panel is a really neat idea, especially if you book match the sap wood on each pair of wedges (like the center of Mark's example table, on which, by the way, staining the sap wood would have been just wrong!). Most of your wood movements issues would be on the bottom, wher the suppor could be covered by the bottom rail. The arc would tend to expand and contract like a Chinese fan. The center of the arc would not move at all. The vertical wood movement at the center would be insignificant, there would be some movement effectively horizontally at the top of the arc, and the outside bottom corners would move vertically a significant amount. That movement could be hidden behind a bottom rail, or even behind the mattress.

Re: Another thought on Cherry/sapwood

#9

Trying to get your intention *LINK*

Gary Smyth

Which of the photos most resembles what you have in mind?


Does the headboard have to be solid? What if a large or small gap was between boards? Seasonal movement would not be an issue and the effect might be similar. A visual backing panel (not attached to the segments) might also assist as a solution. The geometry might be a challenge for long wedges.

You might wish to refer to segment turners for help. There are some very nice jigs for smaller segments on you tube. Jerry Bennett seems to be the originator for one such sled. Under the title "segmentology" there are at least four 20 minute videos. You might find one or more worthwhile.


https://www.youtube.com/watch?v=6Yl-qDN1HtI

Re: Another thought on Cherry/sapwood

#10

Re: Trying to get your intention

Barry Irby

I like the first one. Sort of oriental sunrise? Was actually thinking of something much simper. One thing I don't like about the first one is the long over hang on the top of the footboard. I can see me walking into it and leaving body parts behind.

Re: Another thought on Cherry/sapwood

#11

With space between slats and

Gary Smyth

seasoned lumber I would think that wood expansion of the wide end of x number of tapered slats in a (estimated) four foot length ought not be much of a problem. I'm thinking that the ends will be fitted into a dado at the top and bottom of a frame. Measured spacers between the slats can be cut and adjusted with a bit of play to allow some seasonal dimensional changes. Go for it and let us know how you worked it out..