Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Drawer glide/slide question

Posts

Drawer glide/slide question

#1

Drawer glide/slide question

Chuck

I have a workbench that a friend gave me and for the most part I have been able to modify it to suit my needs except for the drawers. The drawer glides/slides (same meaning?) only open about halfway so storing any tools in them is a hassle, half the drawer is hidden.

I was able to remove one of the drawers and do some measurements and have run into a possible problem. The slides are side mounted and are 14-in long. The problem is they are only 3/8-in thick. When I went to the local home improvement store( ::cough:: Home Depot) all the slide are of the 1/2-in thick variety.

I measured the drawer and opening widths just to verify and the drawer is 22-1/8 in. and the opening is 22-7/8 in. so the 3/8-in is correct. I have been unable to find any slide that are that thin.

Any advice, suggestions, ideas are welcome. I would like to stay away from any major modifications to the drawer or workbench if possible as I have a feeling that I would quickly approach the cost of getting a new workbench (not in the wife's budget).

Re: Drawer glide/slide question

#2

One Way

Mark Mandell - Gone Round In New Jersey

is to set up a 1-1/2" planer bit in your router (table) and cut a 1/8" deep channel in the drawer sides. That will give you what you need to mount new full-extension glides.

Re: Drawer glide/slide question

#3

Re: Drawer glide/slide question

Larry

Make a new drawer. Can you take the old one apart?

Re: Drawer glide/slide question

#4

Re: Drawer glide/slide question

Barry Irby

Any chance it would be easy to switch to under the drawer glides?

I like to buy glides that are rated for several times what I might put in the drawer. They just seem to be much better.

Re: Drawer glide/slide question

#5

Re: Drawer glide/slide question

Joseph Mulherin

I'm with Larry....take the drawer apart and install new drawer sides the proper width for the drawer space including the slides 1/2" on each side.

Modifying the existing drawer by routing the 1/8" into the side will weaken the drawer holding capacity and the drawer might fall apart if there is too much weight inside.

Re: Drawer glide/slide question

#6

Re: Drawer glide/slide question

William Duffield

But you could restrengthen the drawer back to it's original strength by gluing a piece of 1/8" door skin plywood to the inside of each drawer side.

Re: Drawer glide/slide question

#7

Re: Drawer glide/slide question

William Duffield

I'm going to guess it would be difficult. Typical 100 lb. load full extension undermount slides typically* require 1.05" vertical clearance between the drawer bottom and the top of the drawer blade. (*That's for Accuride and similar slides.) Undermounts are usually a bit ore expensive than side mounts of the same capacity.

Re: Drawer glide/slide question

#8

Re: Drawer glide/slide question

Joseph Mulherin

Yes, William, but a sheet of 1/8" door skin at HD costs about $10.00......and what would he do with the remaining sheet? Just installing new sides would be less costly and make a better installation. He has to purchase the slides anyway and I would say buy the 18" or 24".....full extensions.

Re: Drawer glide/slide question

#9

Re: Drawer glide/slide question

Chuck

Thank you all for the suggestions. The ideas follow two paths modify where the glides attach with a router, or modify the drawer.

The router is not an option due to no router at hand, also getting the channel correct would be a major headache I'm afraid without lots of practice.

Modifying the drawer has its own headaches since the drawer is held together with some screws that I've seen on those DIY desks. Not sure what they're called but so as not to have to find another way to connect the corners I would have to take a piece out of the middle from the front and back boards.

I did notice something that might be workable. While staring(glaring) at the workbench I noticed that where the glides attach to the workbench that looks to be a piece of 1/2-in wood that I think I can remove. So here's what I was thinking...the drawers are arranged in a 2x2 setup, there is a board to the left of the drawers, to the right and one in the middle. (1) Could I remove the left and right boards and use my planer(have one of those, no router, go figure) to remove a 1/4-in to get the space I need, or, (2)remove the left and right and plane 1/8-in from them and remove the center board and plane a 1/4 from that.

I think I need to use (2) in order to keep the drawers aligned, but I'm not sure.

Re: Drawer glide/slide question

#10

Re: Drawer glide/slide question

Barry Irby

Not sure I completely understand the design, but if you can remove parts of the bench and either move them or make them thinner to get the space you need without destroying the strength, it should work. Remember, the glides are very sensitive to the width. Some of them say to leave a total of 1" of space, plus a 1/32" Minus 0".