Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Flattening a winded board.....

Posts

Flattening a winded board.....

#1

Flattening a winded board.....

Barry Irby

Somewhere along the way I learned to called a twisted board "winded".

Been trying to prep some cherry for the beds I am making. These boards are about 66" long and 6" wide and 1" thick. Cut them to length and laid them on a flat surface. One corner at one end was about an 1/8" off the table. The opposite corner at the other end was about the same. I used my taper jig and ripped two slivers that tapered from an 1/8" to nothing about two feet long. Glued them to the board with Cyno. Ran them through my lunch box planer with the wedges on the bottom. It knocked the high corners off and flattened the top. Turned it over and planed the other side after removing the wedges.

Seemed to work well. I have used the jointer for this, but this seemed easier. I have hand planed one side, but again, this seemed easier. Any thoughts?

Re: Flattening a winded board.....

#2

some thoughts

Bill Tindall, E.Tn.

Cyanoacrylate glue is not permanent on wood.

I likely would have used the boards as is. When installed they would have straightened. I don't fret flattening and the like as much as some do, especially when the application will bend the lumber into submission. .

Re: Flattening a winded board.....

#3

Re: some thoughts

Barry Irby

You are right about the Cyno. I just stick the wedges on long enough for it to go through the planer. I actually taped some on with blue painters tape but that did not work as well. When I flip the board over I just pop the wedges off. No trouble.

Re: Flattening a winded board.....

#4

Re: some thoughts

William Duffield

I like your idea. But, why bother popping the wedges off? Won't the planer effectively remove them on the first pass on the second side? Of course, that assumes you only have one board to take the wind out of.

Yours is certainly a simpler method than most methods using a sled in the planer, assuming you already have built a tapering sled for the table saw. My tablesaw sled, however, isn't long enough to work well for bed rails, since it was built specifically for table legs.

I use a method with my jointer that doesn't require any sleds or wedges, but it only works on twist in one direction.

Re: Flattening a winded board.....

#5

Re: some thoughts

Chuck in Mtl.

just some amateur observations but cherry seems to have a mind of its own and will move regardless. As an experiment i would do this....clamp the boards into a jig so they cannot move and then soak the whole lot in hot water. let the boards get good and soggy and then dry them still clamped.

Re: Flattening a winded board.....

#6

Re: Flattening a winded board.....

Sgian Dubh

"Somewhere along the way I learned to called a twisted board "winded"."

Barry, you've probably heard one of us Brits talk about boards being 'in winding', i.e., twisted. Slainte.

Re: Flattening a winded board.....

#7

Cherry is a fruit wood......

Barry Irby

and does have a mind of its own. Apple is beautiful, but even worse.

These boards were in my green house attached to my house and are pretty well baked.

I have some more stored down on the family farm about fifty miles away and will have to get more, but I can't understand why I brought these crappy ones home.

Re: Flattening a winded board.....

#8

Re: Flattening a winded board.....

Barry Irby

Some where I have a very old book on building stairs. It came from your side of the pond. It one of my favorite pieces of advice...."If your stairs must have winders, put them at the bottom, because you will fall down them." Many things to learn from the Brits.....

Re: Flattening a winded board.....

#9

Re: some thoughts

Barry Irby

I took the wedges off because it was so easy. The boards had been band sawed and were rough. The wedges came right off. I used them two or three times. I thought of just running them through the planer, but they were so loose I was afraid they would explode and fly out like tiny daggers.

Re: Flattening a winded board.....

#10

Re: Flattening a winded board.....

TomD

I handle a board with wind by grabbing the scrub plane and knocking the high corners off, then I run it through the planer. Obviously I look first at what comes next to be sure I can't reduce my work by crosscutting, or something. The board doesn't have to be great before it goes through the planer, just so long as the worst of the rise is off it.

I won't force a board into position. Wood is one of the best materials at retaining it spring, which is why it is the traditional favorite for bows. Modern glues often creep, so the racking of a twisted board can have an effect over time.

Re: Flattening a winded board.....

#11

Re: Flattening a winded board.....

don stephan

I'm with Tom, I like to have boards that want to be flat and straight before using them.

Keep in mind that you took wood off unevenly from both surfaces, and the moisture content may not have been uniform throughout (learned this from Bruce Hoadley's book). After the first flattening and straightening I stack with stickers for another week to acclimate, the repeat. The 2nd time you should be able to use the jointer straight away to flatten one side, then plane the other parallel.

Re: Flattening a winded board.....

#12

Re: Flattening a winded board.....

Bruce, a MN Galoot

Amen to having straight stuff to begin with. I once ripped a 2" piece off an 8" slab 2" thick. The 2" piece stayed straight and the 6" piece took a very hard left. I was never able to use it for anything other than short pieces.

Re: Flattening a winded board.....

#13

I agree about internal stress....

Barry Irby

and starting with stock that is straight. OTOH, my frugal packrat gene can't stand to throw stuff away. I pick the flattest and straightest parts of the stock for long stuff and then cut the rest down to shorter and shorter pieces.

This material is acclimating as I type. I am trying to stare it into submission.

I need to make friends with my hand plane.

Re: Flattening a winded board.....

#14

Same here

John in NM

A lot of times you can use a less than perfectly flat board depending on whether it will matter for your intended construction. In a door panel it matters a lot, for a bed rail, perhaps not (depends on how it is put together). For a glued up headboard or table top? Also probably not.

If I'm confronted with a board that is less flat than I think the construction can deal with, I usually put it aside for cutting up into shorter parts, either on this project or if doing something where there are none (like a bed) save it for the next one.