Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Cleaning/Repairing lacquer finish question

Posts

Cleaning/Repairing lacquer finish question

#1

Cleaning/Repairing lacquer finish question

Barry Irby

I built a small hall table with a spalted maple top with a lacquer finish. (Deft rattle can lacquer.) A few weeks alter a magazine got left on it for weeks. When removed, some of the paper of the cover had stuck to the top. Sort of delaminated the paper. I am assuming the paper had lacquer on it to make it glossy and it stuck to the lacquered top.

How to remove it? Soak it with water? Lacquer thinner? Scrap, sand and recoat the top?

Re: Cleaning/Repairing lacquer finish question

#2

NOW He Tells Me

Mark Mandell - Gone Round In New Jersey

how long it takes for solvent to completely evaporate from a lacquer finish film?

Sheesh . . .

;)

Not thinner here, Barry, you'll just smear the stuck parts around and leave a mess.

Since you state its a small table and I assume you want the finish to be even when you're done, I'd lightly sand off the violated area starting with 220, vac well, then go up the 600 in quick steps. The idea is just to remove the top surface without sanding through the entire film thickness. Then mask off the rest of the piece with tape and newspaper and recoat the top.

Re: Cleaning/Repairing lacquer finish question

#3

Re: NOW He Tells Me

Dick Coers

Mark's idea will work if you have enough film thickness and the magazine has not melted in too far. I'm no fan of Deft, never have been. The stuff in the can has too much retarder for my liking and takes forever to cure. Always stays softer than straight nitrocellulose and acrylic modified lacquer in my opinion. I had a friend have a vinyl desk saver melt into the top of a magnificent walnut desk.

Mineral spirits may help get rid of a little paper and not effect the lacquer at all. If you use lacquer thinner, it may run over the edge and melt that too. I'd just sand off the top and start over on that surface only.

Re: Cleaning/Repairing lacquer finish question

#4

JL

Re: Cleaning/Repairing lacquer finish question

JL

Paper - a lot of the magazine paper is highly calendered clay coated paper.

They often use "quick drying" nitrocellulose inks.

So what probably happened is that the solvent from the lacquer softened the ink and caused the clay coating to delaminate from the paper.

The clay coating will dissolve in water - probably not something you want on the table. The ink of course will dissolve in lacquer thinner.

Re: Cleaning/Repairing lacquer finish question

#5

I lied, .......

Barry Irby

For the sake of brevity I called it a magazine. It was actually a Report form I use in my Home Inspections. I have them printed and bound and the cover is thicker than a magazine cover, but I am pretty sure it is lacquer coated. I do an inspection, fill out the forms on 3 part NCR paper and give two of them to the client. (Horror of horrors, I am so old school I am still doing them on paper.) I keep the jacket with my copy in it and bring it home with the check and put them on the table. My book keeper stops by and picks them up twice a month. They become my file folder. They sit there for about two weeks under an accumulating load of additional forms.

So, once I fix the top I either need to stop using it for this purpose or find a way to stop the forms from sticking. Should I have a piece of glass cut to fit the top? Or put a coat of shellac over the lacquer?

Re: Cleaning/Repairing lacquer finish question

#6

Re: I lied, .......

AZ in Colorado Springs

I have a plastic desk tray on the top of the upright piano near my front door. My son is in the air force and his car magazine and other assorted mail comes here. Every couple of months I mail it to him. You could use one of those trays.

Re: Cleaning/Repairing lacquer finish question

#7

Time

Mark Mandell - Gone Round In New Jersey

will tell. With warmer weather a solvent finish film may harden up enough in a month or two to take a supplemental top. You'll have to use some clear disc spacers to hold the glass [or plexi] off the surface.

As far as shellac goes, there's no particular benefit over lacquer, but as mentioned, I'd chose a different lacquer than rattlecan Deft. Minwax makes a rattlecan lacquer that's not bad [I've used it on small turnings], but if you want a more durable film for a table that gets a lot of use, you'd be better off going to a poly. General's Enduro Clear Poly is my go-to finish now. It flows and levels so well I've put away the rub-out stuff as the gloss finish is just right "off-the-gun."

Re: Cleaning/Repairing lacquer finish question

#8

Re: I lied, .......

C. John Hebert

If a magazine sticks, chances are everything else will also.....better switch finishes in the future

Re: Cleaning/Repairing lacquer finish question

#9

Re: I lied, .......

C. John Hebert

The more I think on it...sounds more to me that retarder is the problem. I would still refrain from putting anything else on it

Re: Cleaning/Repairing lacquer finish question

#10

Re: Time

Dick Coers

Be cautious about using plastic for the glass spacers. They may just permanently stick if that finish is soft. I'm surprised that there is a solvent issue after a couple of weeks, unless you really laid on the heavy coats or it was cold when you sprayed. I'm really not sure Deft puts retarder in the rattle can version.

Re: Cleaning/Repairing lacquer finish question

#11

Agreed

Mark Mandell - Gone Round In New Jersey

Deft, especially the rattlecan flavor, has always been a low solids film. I've used it interchangeably with spray matte artist's fixatiff on turnings as either a sanding sealer or a light film finish to make dusting the item easier. It'll make something shiny but not much else.