Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Finishing the Front and Back

Posts

Finishing the Front and Back

#1

Finishing the Front and Back

Derek Cohen (in Perth, Australia)

I posted a picture a week ago of completed drawers - now coplaner with one another, and finished in white shellac (Ubeaut).

It was was nice to work at a relaxed pace this weekend, since the goal was to install the drawer handles, wax the drawers (Renaissance), and complete the rear of the carcase. All nice and easy.

The panel for the rear is 1/4" thick Makore, as are the carcase frame-and-panel sides. I made the panel at the start of the build. It had begun as one of the side panels, but it lacked any figure, and consequently I set it aside for the rear of the carcase. This was finished inside with wax and outside with Livos Universal Wood Oil (an Aussie product), which was used on the all the other parts of the carcase.

The panel is secured with nails into the frame. The panel can move laterally via widened (drilled) nail holes. There is a coved attached moulding that tidies up the fitting. The cove matches the cove that is part of the frame-and-panel sides (which were shaped into the frames).


I got to use my restored mitrebox :)




Before the rear could be done, the handles needed to be attached to the drawers. The handles had been a major headache for a long time. I knew what I wanted but could not find ready-made versions. I hunted everywhere like an obsessed dervish!. I was about to build them in Jarrah (my wife's choice to go with the Jarrah drawer fronts) when I found them about 6 weeks ago on eBay! According to the advert they are "antique bronze".

After building a template, and carefully marking, triple checking measurements, I drilled the holes and screwed them on ...




What do you think?

Here is a side. The bow is very subtle, softening the profile ...


What's there to do? Well, I am starting on the top section. The chest needs a crown moulding. This will hide a lid. Raising the lid will reveal a mirror on the underside, plus a recess to place jewellery or cosmetics. The recess will be leather lined.

Then there are jewellery trays to fit (also leather lined). This will go in the top drawer ..


All the drawers have good extension, held horizontal by the last 1 1/2" -2".

Until the top is done ...

Regards from Perth

Derek

Re: Finishing the Front and Back

#2

Re: Good job, nicely done

ChuckInND

I can only imagine the time and expense that went into building it. Nice old hand miter saw also.

Re: Finishing the Front and Back

#3

Re: Finishing the Front and Back

BrianMonumentCO

Derek, Very nice job !

I have a question or two.... In the pix of the very top drawer there are 3 black "blotches" that appear to be a defect in the wood. (My eyes may be playing games on me.)

Are those defects?

Are you going to do anything about them (if they are defects)?

If they really are defects is it common for this type of wood?

If it is common what is the "normal" treatment of the defect?

IIRC jarrah.

Re: Finishing the Front and Back

#4

Re: Finishing the Front and Back

Derek Cohen (in Perth, Australia)

Hi Brian

It is common for Jarrah to have some pitch/resin fissures. Generally they are a minor factor and may be cut out. These boards were dominated in sections with them. I filled the backs, upper and lower edges of the drawer fronts, and chose to leave the fronts alone. Much of the fissures were on the surface only and disappeared when I cut away the bow waste. Those that remained I chose to leave. I think they add some character.

Regards from Perth

Derek

Re: Finishing the Front and Back

#5

Re: Finishing the Front and Back

Doug Wolf

Derek, I've been following your updates of your project and just wanted to give you a "thumbs up" on the final result. I love the handles, the fissures in the front, the finishing of the back, the matching of the grain, the overall design and excellent execution of the job.

The only problem I'm having now is I made the fatal mistake of showing the pictures of it to my wife and now she wants one just like it.

Congrats to a good job!

Re: Finishing the Front and Back

#6

Wonderful Piece

Thomas Skaggs, Foothills of Mount Level

I very much like this piece. It is quite pleasing to the eye. The wood is beautiful and it speaks of good craftsmanship. Well done sir.

T.

Re: Finishing the Front and Back

#9

Waiting For The Top

Mark Mandell - Gone Round In New Jersey

Don't rush it. A fine piece with first quality craftsmanship deserves a proper "crown."

Thanks for the ride-along.

Re: Finishing the Front and Back

#10

Alan Young

"What do you think? "

Alan Young

"What do you think? "

I think this is Like the quiet soft spoken young lass in the far row that you just can't take your eye off.

Re: Finishing the Front and Back

#11

I too am waiting for the top....

Barry Irby

Thanks for posting this. It is inspirational. I suspect no one but another wood worker would recognize the difficulty.

I am anxious to see the top. It looks so elegant now that I fear the top will disrupt the lines.