Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Sliding door Question

Posts

Sliding door Question

#1

Sliding door Question

tom

You guys provided info for hardware recently for an exposed sliding door track. Well the fellow I am building it for dropped off the hardware. But I have a question, the rail is predrilled for lags but since this is a retro install the hole spacing will not line up on the studs.

Has anyone dealt with this situation? I was thinking of a backer board that the rail would be lagged to but it does not provide much depth as I would/could only use 3/4" stock.

Thoughts?

Re: Sliding door Question

#2

Re: Sliding door Question

Keith Newton

I suppose by backer board, you mean a board on top of the sheetrock, or whatever the wall is made of.

Will adding 3/4" out in front cause the door to hang too far out from the wall?

If not, you could cut into the drywall, then put some blocking between the studs, then a filler, then your backer board to hide the excavation.

Re: Sliding door Question

#3

Re: Sliding door Question

don stephan

Drilling additional holes, at the studs, is not an option?

Re: Sliding door Question

#4

Re: Sliding door Question

tom

No, because the rail is pre-drilled and the unused holes would stand out.

Re: Sliding door Question

#5

Re: Sliding door Question

don stephan

I understand, but a 3/4" backer board thickness isn't going to provide enough holding power if the rail is meant to be supported by lag screws. It's not ideal, but the unused holes could be filled with dummy lag screws.

Re: Sliding door Question

#6

Re: Sliding door Question

tom

A thought I have is to use machine bolts through the backer board with "T" nuts then screw the backer board to the studs.

Re: Sliding door Question

#7

Don't Forget

Mark Mandell - Gone Round In New Jersey

you'll need to "restrain" the bottom of the door to keep it from flapping in and out when in use and big-time scratch marks on both the wall and the inside side of the door. That means either a second track in the floor or, at least, a cut groove with several guide pins to hold the bottom of the door stable.

Re: Sliding door Question

#8

Re: Don't Forget

Thomas E Norton

There is a floor guide so that is covered. Came up with another idea. I will bore new holes at the stud locations and plug the existing holes with black plastic plugs from McMaster/Carr.

Re: Sliding door Question

#9

Re: Sliding door Question

Joseph Mulherin

My thoughts: since the guy dropped off the hardware there should be a floor or lower wall rail for a pin to slide in or on to keep the door steady against the wall at the floor. I agree with Keith about installing 2/4s between the studs, then add your 1/4 on top of it and install the upper rail with your lags.

Re: Sliding door Question

#10

Re: Sliding door Question

joe mohnike

forget the wood backer board. Make a backer plate from 3/8 metal, the same dimensions as the rail. Drill and tap the plate to match the holes on the rail use machine bolts. Drill and counter sink the plate to match the studs. 2 each 3-4" screws per stud should be strong sufficient. You could also inset the plate in the sheet rock. Good luck.

Re: Sliding door Question

#11

Re: Don't Forget

Barry Irby

Is there no header above the door opening to bolt into?

Are the holes in the track on the same centers as the studs? Do you have enough length of track to slip it sideways enough to line up the holes and then trim the ends of the track to match the opening?

Re: Sliding door Question

#12

Re: Sliding door Question

tom

I like this idea. I have a welding fabrication shop close by. I could have them do the fab work and then I would just paint it.

Thanks!

Re: Sliding door Question

#13

Don't Be Too Surprised

Mark Mandell - Gone Round In New Jersey

at the price of that piece of steel. And then there's the fabrication shop time . . . ;)

Re: Sliding door Question

#14

Re: Don't Be Too Surprised

tom

It will be passed on to the customer.

Re: Sliding door Question

#15

Options

Mark Mandell - Gone Round In New Jersey

Make sure you're within "budget" so it doesn't eat your margin, and give the customer the option for the increased cost.

You won't be the first guy to hear "Why didn't you tell me about how much that would cost?" You may still get paid but you might loose a customer for more work.

Re: Sliding door Question

#16

Re: Options

tom

In jobs like this they are Time & Material.

Re: Sliding door Question

#17

Save Some Money

Mark Mandell - Gone Round In New Jersey

With 16oc studs 1/4" steel will be plenty strong enough in this application, and much easier to work.

Re: Sliding door Question

#18

Re: Save Some Money

joe mohnike

depending on the diameter of the bolt and the thread pitch 1/4 may not be thick enough, ask the metal shop for their opinion.

Re: Sliding door Question

#19

Re: Save Some Money

Mark Mandell - Gone Round In New Jersey

An interior door should never be more than 50 pounds. A high weight sliding door with children involved is asking for a trip to the ER to have fingers repaired if not sewn back on. 1/4x24 bolts would be fine for the track and 2-1/2" #12 screws more than adequate in the studs. 1/4" bolts need no more than 1/4" plate as the bolt will fail before the plate. At the price of steel today, it's a waste (IMHO) to use anything more.

I have my electric winch in a ceiling-mounted barn door track over my lathe with 1 #10x 3" screw in each joist. It lifts more than 500 pounds with no issues at all.