Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Slab to foundation joint seal?

Posts

Slab to foundation joint seal?

#1

Slab to foundation joint seal?

Tim Greif - West of Chicago

My river house has a two car attached garage that we're turning into living space. The floor slab abuts the cement block foundation. I noticed this winter during extremely cold, windy weather, there is a cold draft coming up through various points in the joint between the slab and foundation. Before we close this up and lay carpet, I want to seal these gaps up. I'm not sure which is the best approach - either use expanding foam or use some type of caulk or driveway crack sealer, either the pourable type or the caulk tube type. Anybody done this before?

PIC below shows the joint. This is a cement block foundation wall. I've filled the block cavities and the slab is flush with the top of the foundation wall. The crack varies from nothing to maybe 1/8 inch depending on location. The outside north and south walls are the most susceptible to wind influence.

Re: Slab to foundation joint seal?

#2

Re: Slab to foundation joint seal?

Ralph Lipeles

I had a summer home with a poured concrete foundation. After a few years it developed a crack. I looked at the available solutions. Some were complicated. Some were expensive. So, I came up with my own. Since nothing could keep the foundation from moving, if it wanted to, I decided that I only needed to fill the crack. I used a concrete drill to open up the access to the crack at the points where it was only a little bit open. I then blew out the crack with the air gun on my compressor. For the filling I used an expanding foam in several places along the crack. I used an old hand saw that was ready for the scrap pile to remove the excess that had squeezed out. The fill did a great job and never had to be redone.

Re: Slab to foundation joint seal?

#3

Re: Slab to foundation joint seal?

Barry Irby

My only reluctance to what Ralph said was I wonder if the foam will expand with enough force to open the crack further. (A friend of mine wanted to insulate his bath tub and shot Great Stuff under a 400 Lb cast iron tub. It picked it up about an inch.) Maybe use the low pressure version designed for windows.

Re: Slab to foundation joint seal?

#4

Re: Slab to foundation joint seal?

Ralph Lipeles

The force should be very low. The foam is a bunch of air bubbles that is not constrained. The extra should just run out.

Re: Slab to foundation joint seal?

#5

Re: Slab to foundation joint seal?

Dick Coers

I'm with Barry, I've heard crazy stories about expanding foam. I'd use foam backer rods and self leveling caulk/sealant.

Re: Slab to foundation joint seal?

#6

Re: Slab to foundation joint seal?

Barry Irby

Ralph, I don't want t be a Nervous Nellie here, but besides the bathtub story I personally nearly ruined a window by shooting foam in around it. That's when I learned about the low pressure Great Stuff.

As an aside, I watched a company "slab Jacking" sidewalks that had settled. They drilled a hole though the slab that was about an inch and a quarter. (skipping a few details here) they blew air under the slab to lift it. The machine entrained granite dust to eventually support the slab. The Air pressure? 5 PSI. Sounds impossible until you multiply 5 times 144 and 720 pounds per square foot. The guy doing it told me that they woudl park their truck on the sidewalk to hold it down if it went too high.

the point is that if the crack is already opening between the OP's slab and wall, he does not want to add much if any pressure.

Come to think of it, this might be a good application for some of the duct seal mastic. Just slather it over the surface and seal the tiny cracks.

Re: Slab to foundation joint seal?

#8

One more thought....

Barry Irby

You mentioned feeling cold air come up through the cracks.....

Cement blocks are only about 95% solid. That is, 5% voids. The wind will blow right through them. I know this from personal experience. Back in the day I stood with my back to a huge block wall on a construction site on a cold windy day. I could feel the air coming through the wall on the back of my neck.

Surely some blocks have differing resistance to air flow but, while you have the chance you might want to seal the tops with some sort of mastic or check with a commercial paint suppler for "block fill" paint.

And caulk along the base of the wall.