Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Glaze for a penny table top

Posts

Glaze for a penny table top

#1

Glaze for a penny table top

Jon

Hello All,

I just made a pub table for my basement. Right now the paint is drying so I am investigating my next step. On the top I am going to make a pattern out of pennies. I have a 1/4" lip that goes all the way around the border to contain the glaze. I wanted to know what type of glaze you have used that gets good results. Also, if you could offer any tips of what to do and what NOT to do. I have seen 2 different types at the box stores: Parks Super Glaze and Farnwood Glaze Coat. Both have mixed reviews. Any help would be great. I will post a picture when complete. Thanks Jon

Re: Glaze for a penny table top

#2

Re: Glaze for a penny table top

Howard Acheson

There are a number of epoxy pour-on products available. Google "epoxy pour-on". Be sure to follow the directions. They can be problematic . They also are easily scratched and almost impossible to repair.

Re: Glaze for a penny table top

#3

Thought to use glass?

Gary Smyth

Any thought to solve the problem of pouring and waiting and scratches by using float glass? if necessary you can provide wire gauge vent holes from the underside and seal the edges with clear silicon to prevent edge leaks. Longer life to keep it clear and easier fix when its time.

Re: Glaze for a penny table top

#4

Re: Thought to use glass?

don stephan

Did a poured epoxy finish for a customer once. Never again. Bubbles, out of level, border dams, sanding/sanding/sanding and scraping . . .

Re: Glaze for a penny table top

#5

Re: Thought to use glass?

Tim Caley

You can get the bubbles out of the two part epoxy solution by lightly heating the area with a small torch. I have had good luck doing this in the past.

Re: Glaze for a penny table top

#6

Get The Air Out

Mark Mandell - Gone Round In New Jersey

with your shop-vac

1. Cut/drill a hole in a 5gal bucket that will fit your vac hose.

2. Get a piece of plexi or glass that will cover the top of the bucket but allow you to see the contents and make a good seal on the rim.

3. Mix your epoxy well in a bowl that has at least twice the volume needed, but will fit into the bucket.

4. Put the bowl into the bucket, put the "top" on, turn on the vac and bring the hose to the hole.

5. You will see the epoxy start to foam up in the bowl. That is the air being drawn out.

6. Pull the vac away after a few seconds and let the mix settle back down.

7. Repeat 4,5 & 6 until the liquid no longer reacts to the vac suction.

Your epoxy can now be carefully poured and you will have a crystal clear epoxy with no air bubbles.

Re: Glaze for a penny table top

#7

PS

Mark Mandell - Gone Round In New Jersey

This won't work with the junk "5-minute" stuff that's fast-setting.

Re: Glaze for a penny table top

#8

Are you talking about entrained or dissolved?

John in NM

A good vacuum cleaner will probably develop enough sealed suction to burst entrained air bubbles from mixing, but not enough to remove dissolved gasses.

Depending on the resin used, getting the entrained air out might be sufficient, but some resins tend to seemingly make new bubbles from dissolved material.

That foaming effect you describe is something I associate with dissolved gasses that come out around 20" Hg, but since I've only done this with a vacuum pump, I could be wrong about that. A good shop vac might develop about 6" Hg if the pot is well sealed.

Re: Glaze for a penny table top

#9

Not

Mark Mandell - Gone Round In New Jersey

talking about making optically pure lenses or arcane specialty resins.

Just the generic stuff us woodworkers use and getting a clear coating that's cefgw.

Before


After


Re: Glaze for a penny table top

#10

Its all arcane in its way....

John in NM

Specialty is largely a matter of perspective - what seems run of the mill to us is a specialty to a guy who does a lot of elastomer casting or some such.

But yeah, that answered my question - popping the stirring bubbles is enough to get the results one wants from these epoxies. I'm going to guess they cure slowly and don't get especially hot?

Re: Glaze for a penny table top

#11

Heat's The Enemy

Mark Mandell - Gone Round In New Jersey

Epoxies, being therosetting compounds, can generate a fair amount of heat. This can be reduced by using long-acting hardeners. The thicker the pour, the more heat will be generated. Pour epoxy thicker than 1" thick and you're flirtin' with deformation, cracking, and discoloration. This is why manufacturers will tell people not to thin their resin with alcohol; as the mix heats up it will actually boil the alcohol out and you wind up with a block of foam rather than solid plastic. DAMHIKT

In the example I poured 1-1/2" thick but used a very slow hardener and mounted a fan to blow on the surface. Took the pour overnight to start to gel and 2 full days before it was fingernail hard. Had to wait a full week before starting the sanding and finishing process.

Re: Glaze for a penny table top

#12

The foam effect....

John in NM

I had the same thing happen with some urethane casting resin, only the bubbles were made by steam from water vapor - tiny amount of condensation in a glass mixing jar was all it took :D (I now use plastic cups).

I also tried some proline black colorant once, same thing. The carrier boiled and gave me a pretty holey casting :D That particular urethane can get to 300F on a big part.

Looks like you got great results with that slow cure, the fan is a good idea.

Re: Glaze for a penny table top

#13

One Step Further

Mark Mandell - Gone Round In New Jersey

is actual temperature control. When I was investigating polyester resin as an alternative for bronze casting I actually used a refrigerator to control the heat and slow the set. Held at 42°, which was just above the stated minimum for the catalyst, I could get decent, but not perfect, castings up to about 2" thick. Couldn't get rid of the damn pink hue in that resin however. That was when Lucite and the acrylics were just getting started (1973), but they needed very expensive equipment so never went there.