Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Table Saw Switch Modification Question

Posts

Table Saw Switch Modification Question

#1

Table Saw Switch Modification Question

Gary Smyth

Reading ChuckInND responses reminds me to ask. Are there pictures of the set up of different saw on/off switch locations? I have a Jet contractor's 10 inch (the old JTS 10). It serves me well. The switch is on the lower left of the cabinet well under the table. Current mount is to the front, and I moved the switch box as far as possible outward but remains mostly inside the cabinet. I am used to it so I know pretty much by stabbing BLIND where it is located even with large sheet goods blocking direct view on the table. I have tried to seal the switch box, but fine sawdust continues to creep in and about every year or so it clogs the contact points so that the saw will not turn on. Seems like it happens at the worst time. Much of the problem is original engineering in that the motor/switch wires are blocked by a combination of motor wire end is sealed in the motor housing, the table top, saw trunnion, and the cabinet, making access hard to reach, the metal cut out is sharp and all existing wire connections are very short.

Next time it happens I'm thinking to make a change. I don't much care what it looks like only that it is convenient and works -- every time. I also want to avoid the possibility of mistakenly hitting the switch.

I'd like to see how others have reduced or eliminated the sawdust problem and making the on/off switch location easier to reach, less likely to clog, and safe. Pictured is existing.

Re: Table Saw Switch Modification Question

#2

Re: Table Saw Switch Modification Question

David Yoho

I had to look up an image of your saw to know what the front looked like. I have a Jet 10" cabinet saw but was unfamiliar with yours. I believe I would remove the switch entirely from its existing location and close up the opening however you like. I'd add the proper gauge and type of wires to the switch ends and extend them through the left side of the cabinet. Drill the hole and leave room for a rubber grommet to protect the wires. Find an appropriate box for the switch and mount it to the left front end of the stamped extension so the box is below it.

This gets it out of the dust and closer to a point you can easily reach.

Re: Table Saw Switch Modification Question

#3

Re: Table Saw Switch Modification Question

David Bair

On my 15-year-old JET contractor's saw, the switch is mounted on the exterior of the saw and has never needed service. It attaches to the lip of the wing, nearer to the operator.

Re: Table Saw Switch Modification Question

#4

Knee switch

Hoa in Alameda

How about moving the switch out to the edge of the tablesaw top, under the fence rail?

Here are some old photos of my (current) TS switch. Of course I can't turn on the TS with my knee, but I can turn it off with almost any body part :)

In photo #1, on the right is the switch of the router in the cabinet under the TS's right wing.

Photo #2 shows how the paddle is attached to the rail. The bracket came from an out-of-spec Incra miter gauge.



Re: Table Saw Switch Modification Question

#5

Re: Table Saw Switch Modification Question

ChuckInND

On the 10' Delta 34-445X that I bought new in 1995, and the 9" Rockwell 34-607, both had a electrical box that was mounted to the inside of the cabinet, lower left front side, and they used a small toggle switch. Since the electrical box was mounted inside the cabinet, it would fill up with saw dust. It's another reason that I relocated the box and switch to under the fence rail. The small hole where the small toggle switch was mounted to the front of the cabinet I covered with a chrome round plug.

Re: Table Saw Switch Modification Question

#6

Bingo!

Mark Mandell - Gone Round In New Jersey

I haven't turned off my table saw with other than my knee is more than 15 years. Knee/kick switch allows me to maintain control over pieces of wood on the table as well as visual contact with everything

Re: Table Saw Switch Modification Question

#7

On dust getting in to the contactor...

Grant in Iowa

I'd make a change sooner rather than later. If dust is creeping in to the switch box, and interfering with the contactor, I'd ditch it or at the very least do an overhaul and get it out of the saw cabinet away from the dust. Contacts make arcs each time they make or break, and those arcs could easily make a fire if sawdust is involved. And the plastic boxes they come in would not reliably stop such a fire to my satisfaction.

Consider purchasing a single phase (assuming you don't have 3 phase power) magnetic starter assembly. This will allow you to mount it so you can implement a paddle or crash bar turn off feature like shown in a previous post. Several companies make them available, such as Griz, Woodstock, etc.

An added benefit is a magnetic switch will not re-energize when power fails and comes back on. A rare event, but are you ready to fumble around in a dark shop when the power is out and you had the table saw on?

If you need help with wiring, or what to buy, ask.

Regards,

Grant in Iowa

Re: Table Saw Switch Modification Question

#8

Re: Table Saw Switch Modification Question

ChuckInND

Here are the two saws that added paddle switches too. https://sites.google.com/site/deltacontractorstablesaw/

Re: Table Saw Switch Modification Question

#9

Re: Table Saw Switch Modification Question

pecker

I don't have that particular saw, but I added an aftermarket paddle switch, similar to what another replier mentioned. It was a bit tricky attaching to the fence rail. See pics below.




Re: Table Saw Switch Modification Question

#10

Re: Bingo! +1


Re: Table Saw Switch Modification Question

#11

Witch switch...er...which...

Tom Dunlap

...magnetic switch would be recommended?

What criteria would I use to compare one and another? I'm guessing that the switch must meet power requirements of the motor. What more?

Thanks

Tom

Re: Table Saw Switch Modification Question

#12

Thanks for the input but as Tom

Gary Smyth

mentioned above, which switch is recommended? I looked at magnetic switches online and the price range went from $25 to a tad over $150. I hope I wouldn't need to look at a $150 dollar problem solver owing to it being a table saw. Is the switch based on load? Duration of the saw being on? Would a electrical supply store be able to supply a proper switch, or would a big box, woodworking site, manufacturer be the best source?

Re: Table Saw Switch Modification Question

#13

Head to your home center

Hoa in Alameda

OK, a magnetic switch is out then. Frankly, for a homeshop, the only advantage of a magnetic switch is that if you lose power (or the saw is unplugged) when the switch is at the "on" position, when power is restored (or the saw is plugged back in), the saw doesn't start. I don't know how often this happens.

If I were you, I'd go to a home center to fetch a heavy duty 20A commercial-grade switch (the one with a big rocker (e.g. Leviton Decora) is easier to turn into a knee switch), a 1-gang weatherproof box, some 14-ga rubber cord, and a few brackets for mounting. With some elbow grease and scraps around the shop, I'm sure you can turn that into a knee-switch mounted outside the saw cabinet. Later on, if you find a more "elegant" switch, you can probably re-use most of the things you did, and will "waste" only a few $ for the switch.

That was what I did for my bandsaw (18A 120V motor) until I found a used magnetic switch for cheap.

Re: Table Saw Switch Modification Question

#14

Re: Switch source

ChuckInND

I bought the paddle switch from Woodworkers Supply. I run the wires to the outside of the cabinet, and wired it for 230 V.