Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Sears Drill press overhaul

Posts

Sears Drill press overhaul

#1

Sears Drill press overhaul

Philip Duffy

My 'ole Sears DP is making horrid noises from the motor and pulleys. Looking for ideas on who/how to get it overhauled (?). Perhaps the most economical answer is to buy a new one but - -- the sentimental value is very high. It is the first big tool I ever bought, some 24 years ago. All ideas appreciated. Philip

Re: Sears Drill press overhaul

#2

Re: Sears Drill press overhaul

Hank Knight

Philip,

Sears made some really good drill presses back in the day. I have a friend that has an old Craftsman he thinks the world of and wouldn't trade for anything. He ran into a problem with replacing his belts. His machine used non-standard, little thin drive belts. He finally found replacements online and was back in business. Your press is probably worth a little time and expense to recondition. It's not hard to do and should be well within the capabilities of someone with modest mechanical skills, like me. Your machine may have the narrow belts, but most everything else, bearings, chuck, etc., should be standard and easily available. Motors can be rebuilt by electric motor repair services, or replaced if necessary. If you need narrow belts and have trouble sourcing them, drop me a note and I'll find out where my friend found his replacements. Good luck.

Hank

Re: Sears Drill press overhaul

#3

http://www.ereplacementparts.com/

del schisler

may have all the parts you need

Re: Sears Drill press overhaul

#4

Re: Sears Drill press overhaul

Ralph Lipeles

It should be pretty straight forward. The only tricky part might be the return spring. It might have a preload that you will have to duplicate at reassembly. Try to get a parts list so that you can put the disassembly in perspective. Take careful notes on everything that you do. Pictures are also a help. I usually put the parts in plastic bags or use pieces of masking tape to assign part designations. Clean the parts with kerosene or mineral spirits. Inspect the parts to determine if any might want to be replaced. Parts are sometimes available from Sears, Independents or eBay. Bearings are standard and replacements can be obtained from a local supplier or on the internet. Reassemble in reverse order of the disassembly.

I've done a couple of drill presses. I like to clean up the column with sandpaper or coarse steel wheel. A also paint the base and any cover plates with grey spray paint.

If you don't have a parts list, look on the internet, eBay or post here for it.

Re: Sears Drill press overhaul

#5

Check the back tensioner

Gary Smyth

Don't panic (yet). I have two drill presses by Sears. Like yours they are getting long in the tooth. Over time I sometimes get the racket you describe. Always (so far) it has been one of two problems.. 1. the tensioner rod has slipped. Located at the rear right side. Rotating it back to stretch the belt has solved the problem. Also you can get a racket when 2. the press is near a wall and/or the lift up top cap gets knocked out of its normal alignment. Mostly these get unnoticed until the racket suddenly occurs. If that solves the problem the relief is palpable.. The thin belt is of concern, but as mentioned they are available but when mine goes I'll be looking for different pulleys and a wider, heavier belt. One other problem might cause a slow return. I've never had a return spring problem, but I have had a slow return when the quill lock gets tightened inadvertently. Check that too. These may not solve your situation but try these first as the cost is zero and takes less than a minute.


Re: Sears Drill press overhaul

#6

Re: Sears Drill press overhaul

walta

The last time my drill press made that noise it had gotten pressed against the wall and that made it knock and rattle.

If that is not it try removing the belt and see if the problem is in the motor or in the spindle.

Walta

Re: Sears Drill press overhaul

#7

Re: Sears Drill press overhaul

Philip Duffy

Thanks for all the good advise and recommendations! I knew you experts would come forth with the best course of actions. Thanks a ton! Philip

Re: Sears Drill press overhaul

#8

Re: Sears Drill press overhaul

George Koch

Philip, If you find the part that's causing the problem, you might get the replacement by going to SearsPartsDirect.com and enter your model number to pull up the diagram, manual and parts numbers for that tool. George

Re: Sears Drill press overhaul

#9

Re: Sears Drill press overhaul

bobby stout

If you realy want to overhaul your press, you can up grade it with a 3 ph 3/4 hp motor and a 1 hp VFD and remove the idler pulley and you can have a variable speed drill press that is assume. I think I spent around a $250 bought all for Automation Direct. http://www.automationdirect.com