Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

OT Shower Body Sprays

Posts

OT Shower Body Sprays

#1

OT Shower Body Sprays

Dustmaker Mike

Well I am doing a lot of work around the house this winter. The last project I will be doing is installing a new shower. I don't have enough room for a tub. So my questions are.

I am pretty sure I only have 1/2 in copper feed lines to my shower faucet right now. Which keeps the pressure pretty well for a shower head. Will this be enough for running body sprays? Or do I need 3/4 inch feeds to the faucet?

Is there a good site to look at to get ideas of the rough in work?

I know I need a second divert value to control the body sprays is there anything else needed?

How is PEX verses copper to work with? Also will it flow the same pressure as the copper will in the same size?

I am pretty comfortable running copper and plumbing in general. I have always used copper but I am thinking the PEX will be easier to run. What tools would I need for the PEX. Think home owner not contractor.

Thanks

Mike

Re: OT Shower Body Sprays

#2

Pex

John in NM

I've done one structure with Pex, having always used either copper or cpvc previously.

As I understand it (and I may not) the industry standard with Pex is to use small lines running from a manifold. Pex in sizes under 3/8" is fairly bendable and easy to run.

However, when we were building our house, we would occasionally house sit at a house that had horrible water pressure/volume, in spite of having a booster pump set up and a large storage tank. I attributed this to long runs of small gauge Pex.

So when I installed it building our guest house, I used 3/4" and 1/2" as if it were regular pipe. Worked fine for pressure/volume, but the downside is that in these diameters it is not especially flexible - you can treat it as a flexible line still, but installation is not what I would call easy.

If there is a next time with Pex, I will treat it as I would rigid pipe. The trouble with that is that there will be more fittings to install, which increases cost and effort, and reduces Pex's strengths when it comes to frozen pipes (that may not be a concern in your area). I still think it would be cheaper and easier than soldered copper though.

As to tools, I bought a simple crimp tool that works with a pair of vise grips. Worked fine for a 1 job homeowner tool. For doing a large job or multiple jobs, I think it would quickly become annoyingly slow compared to the typical heavy ratcheting crimper. There are also crimpless connections, but I have no experience with those. If you can find a plumbing forum (seems like there are forums for everything), just lurking there for a little while would probably give you a good idea of all the pros and cons of the various connection systems.

Personally, I do like Pex in the larger sizes and using the crimped copper rings. I would probably use it again if I were building again, but I wouldn't depend on my ability to bend the stuff.

Re: OT Shower Body Sprays

#3

Re: OT Shower Body Sprays

Ray - Middletown, IN

I have 2 body sprays and the main shower all running at the same time with no noticeable loss. All done in PEX 1/2"

Re: OT Shower Body Sprays

#4

Re: OT Shower Body Sprays  *LINK*

John McGaw

I don't know if this is directly applicable but during my last remodel I installed a 'shower bar' unit with body sprays and it functions quite well with 1/2" copper supply lines.


Shower Bar

Re: OT Shower Body Sprays

#5

Thanks I looked at them

Dustmaker Mike

and was going to use it as a back up. I will have the walls down to the studs, so I figured I would run a few body sprayers at the same time. If they where easy enough.

Re: OT Shower Body Sprays

#6

Re: Thanks I looked at them

Stuart Johnson

I don't know how body sprays work but I had to remove the restricter (sp) washer from both the shower head and when replaced with the hand held shower head. The flow is so restricted it will probably be the head rather than pressure that causes problems.

Re: OT Shower Body Sprays

#7

Re: OT Shower Body Sprays

Barry Irby

Look up "De-zincafication" or Pex failures. The brass used in some of the fittings had too much zinc in them and its coming out ruining the fittings and failing. It may have something to do with water chemistry. Something to think about.

I have done several houses with PEX. I liked it. I bought a tool set for it that looked like bolt cutters with interchangeable jaws for half inch and three quarter inch fittings. Less than $150 at Lowe's. It worked well. I liked Pex, but the tools got stolen and rather than buy another set I switched to CPVC. I make repairs with copper and can work with it, but it gets stolen, so I use the plastic stuff to avoid feeding the thieves. Half inch should be fine for a shower, even with sprays.

Re: OT Shower Body Sprays

#8

Re: Thanks I looked at them

John McGaw

I wasn't trying to sell you on the idea of a shower bar, just letting you know that the volume of water through 1/2" pipes, at least with my water pressure, is more than adequate for at least a couple of body sprays. I actually did that bathroom for my elderly mother before she moved in and she uses nothing but the hand spray thingy so volume is a moot point anyway.

Re: OT Shower Body Sprays

#10

Re: OT Shower Body Sprays

Jay Lombardo

Mike, about 5 yrs ago I installed a new shower with one shower head and 3 body sprays on a half inch line. I have very good city water pressure so there is no issue there. It all works OK but if I had it to do over I would opt to go up to 3/4. I like them on the pulse "massage" mode and when I open everything there is a distinct difference in pressure that I think the larger line would eliminate. Mine is in copper, haven't gone the pex route yet.

Re: OT Shower Body Sprays

#11

The pipe is probably not the issue

Tim Greif- west of Chicago

We did a bathroom remodel last year (built in 89) and the contractor talked me into "updating" my shower control. Biggest mistake I ever made. Previous shower valve was a Moen-trol push pull style feeding two shower heads in a 3 x 5 foot shower, all with 1/2" copper on the second floor. LOML picked out the new control, also by Moen. It's an attractive rotary handle "Posi-Temp" model. Probably my fault for not researching it. The flow capacity of this "updated" model is less than 2/3 of the old control. It's fine for a single shower head, but clearly less than I was used to with the old valve. Even with the shower heads drilled out, it still has less force than the old setup. Do yourself a favor and look closely at the flow specs of any valve you select, especially if you have it feeding multiple outlets. Im not a fan of the gentle rain shower feel. I rather like getting water blasted. Just sayin'.