Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Holy Drawers Batman!!!

Posts

Holy Drawers Batman!!!

#1

Holy Drawers Batman!!!

David Yoho

This morning I went out to the shop to begin dimensioning the rough cherry for the top to the monster dresser I'm building. More on that in a minute. Horizontal real estate is at a premium in my shop. I had all sixteen drawer boxes stacked in a number of spots but needed those spaces while I was working the cherry boards through the saw, jointer, and planer. The only place I had where they wouldn't be in my way was at one end of my free-standing bench. So I stacked them - eight to a stack - and started working on the cherry for the top.

Below is a shot of towering drawers and the cherry and figured Makore fronts that will be attached later.


I noticed the last wood I ran through my planer had enough ridges on it indicating I needed to change out the blades. I pulled a new pack down from storage and began the process of changing or flipping blades. To my surprise I found only one edge had been used and I didn't need to replace them. So I flipped them and put everything back together. The cherry I dressed this morning came out clean and smooth as silk. Wow, what a difference sharp blades make!

I've been bogged down trying to decide how best to make the top for the dresser. It will be just under nine feet long. The two biggest issues for me was trying to joint nine foot 4/4 rough stock and end up with something that didn't look like a giant wedge and not enough space to feed it in and out of the planer. Another issue was how I was going to assemble it if I cut the nine foot stock into smaller pieces and still have it be strong while allowing for movement. I came up with several ideas that just didn't work in my mind. Then yesterday I was looking at my hardwood floor and it came to me - I could cut the boards into shorter lengths, used spline joints like tongue and groove flooring, and stagger the lengths so the butt joints didn't line up. So basically I'll be cutting the three nine footers and then putting them back together. This will still give me the plank look I originally wanted and it was easy to end up with a finished thickness of 15/16. There may have been other solutions to this but my poor brain didn't come up with anything better.

Oh, and now that I need my bench to work on the pieces for the top I had to move the drawers again :(

Re: Holy Drawers Batman!!!

#2

Re: Holy Drawers Batman!!!

Thomas Skaggs, Foothills of Mount Level

Looks like an opportunity to play giant Jenga. :D

T.

Re: Holy Drawers Batman!!!

#3

Re: Holy Drawers Batman!!!

AZ in Colorado Springs

I'm building a 9' long entertainment stand for a friend and I did the same thing for the top. The two shelves below the top will be frame and panel. (Four sections with vertical dividers between them.) So I had to joint the edges of the front and rear rails of those two shelves by hand -- four boards. But the top was glued up as you described.

Re: Holy Drawers Batman!!!

#4

Re: Holy Drawers Batman!!!

David Yoho

That's basically how this dresser is laid out - 4 sections without the shelves but with drawers. Since this thing needs to go in an upstairs bedroom I had to make it in two cases in order to get it all up the stairs and into the room. Once there, I'll screw the two cases together (like kitchen cabinets), lay the top on and attach, and install the drawers.

I've never made a top or anything else this way but it's the only method that made sense to me. The width (front to rear) will be 19 inches. I'm using 3 boards that I cut into lengths. The two outer boards will be 6 inches wide and each cut into 3 pieces the same length with the center being 4 pieces at 7 inches.

I think the tricky part when assembling may be pulling the butt joints together so there's no gaps. I've heard about attaching clamp blocks to the two parts with hot glue but I think I'll do it a little different. Instead of hot glue I'm thinking of using hide glue. The blocks will be easy to remove later with some hot water and some gentle persuasion.

The other issue I see is trying to assemble and glue a nine foot top that I'd like to keep on a flat surface when that surface is only 5 foot long. I'll probably try making it in two sections, let them dry, and then put them together. Should work.

Re: Holy Drawers Batman!!!

#5

Re: Holy Drawers Batman!!!

AZ in Colorado Springs

For shorter laminated panels I've put a clamp across the joint as you discussed. For longer panels I cant the clamp a couple of degrees so when I tighten the clamp it pulls the piece over to snug the joint in two directions. I glue it up one strip at a time, jointing the edge before going to the next strip. And I use pieces of scrap as clamp pads to avoid denting the edges so there's less jointing before continuing to the strip of boards.

I've done this a few times on painted projects. It's a good way to clean out the scrap bin

The entertainment cabinet will have a row of four drawers on the bottom tier, then two shelves then the top.

Re: Holy Drawers Batman!!!

#6

Good idea

David Yoho

I never thought about doing one board at a time and then gluing them up like a regular panel. I'm going to think that one over. Actually, I'm already thinking of a modified way but still better than my original thought. Thanks for the idea!

Re: Holy Drawers Batman!!!

#7

something I don't understand

Bill Tindall, E.Tn.

So the top is 9' x 19" and the issue is gluing it up from some number of boards?

I don't see why this glue up is any different than any panel 19" wide. A board this long is going to be flexible about its length so a perfect straight joint is not essential. And, the finished top is going to be flexible enough to be able to be pulled down upon the cases no matter if it is perfectly flat or not. I would glue up the panel one board at a time so that I got near perfect alignment along the length.

Re: Holy Drawers Batman!!!

#8

You are right

David Yoho

I think it's more about me being obsessive about something that's "out of the norm" for me. Sort of "unchartered waters" as far as putting a panel together. However, this is where a dry run or dry fitting first will help. I actually don't see any real problems as long as I can get the butt joints snug and I think I have that covered.

I agree with your point about flatness and flexing. There will be enough attachment points to pull the top down along the length. I plan to begin the assembly process tomorrow. I think it will go just fine.

Re: Holy Drawers Batman!!!

#9

The Glue Up

David Yoho

I began gluing up the top this morning. Since my bench top is only 5-feet long, I'm doing it in two sections first. After those set up I will glue the two halves into one 9-foot panel. So far, so good.