Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Cold Weather Finishing

Posts

Cold Weather Finishing

#1

Cold Weather Finishing

Bill Tindall, E.Tn.

I am spraying the table with conversion varnish today. The temperature is around freezing. So how do I do it? Actually, it is easier to get a good finish when it is cold than when it is warm. The finish flows nicely when it is cold, smooth as glass.


First, get everything warm, especially the wood. The heat from the wood is what will flash the solvent most effectively. Then rush outside to spray. I spray outside and let the bulk of the solvent flash off for about 5 minutes.

We have a small downstairs bathroom that I can get warmer than the rest of the house. The table starts here and returns here to cure the finish. This product will harden enough to scuff sand between coats in an hour or less.

For a while the house has the sweet smell of toluene but it is a tiny price to pay for getting something finished once or twice a year in the winter. Personally I don't find the smell of solvents objectionable. I associate it with getting something done at last.

PS the table is upside down on a lazy susan. A lazy susan makes spraying easier as the piece can be rotated into ideal position and I don't have to move.

Re: Cold Weather Finishing

#2

Dale Lenz

Re: Cold Weather Finishing

Dale Lenz

My problem that I'm thinking of, is moving the wet piece in question without messing up the finish....

Re: Cold Weather Finishing

#3

Re: Cold Weather Finishing

Ron Berlier

Dale, please email me at alive82071@mypacks.net.

Re: Cold Weather Finishing

#4

carefully

Bill Tindall, E.Tn.

Actually it is dust-free in minutes and easier to move than it could be. But it is not hard yet, so must be move with some care. In any case I am careful and never had a problem. A car, SUV or van makes a dandy greenhouse for curing also. In fact the table was short enough to go in our SUV and that is where it is curing now. Will go to warm bathroom when the sun is lower.

Re: Cold Weather Finishing

#5

Re: Cold Weather Finishing

TomD

Bill, what conversion varnish do you use?

Most solvents smell pretty nice, at least the ones we are allowed to have. My kids like them, free of preconception about effects on health or the environment.

Re: Cold Weather Finishing

#6

Re: Cold Weather Finishing

Charles Yawn

What about how the finish is applied - spray, brush? any cold weather tips about that?

Re: Cold Weather Finishing

#7

Re: Cold Weather Finishing

Bill Tindall, E.Tn.

I am spraying. Spraying makes lots of overspray that could present a fire or health hazard in a confined space. Hence the outdoor location for spraying.

When I am brushing I do it in the shop where it is warm, like it was done for centuries before people became convinced that a whiff of solvent was harmful.

Many finishes will not cure properly unless they are cured warm, including the conversion varnish I am using. Hence, the warm environment cure.

Re: Cold Weather Finishing

#8

Re: Conversion Finishes

Mark Mandell - Gone Round In New Jersey

When considering the "new" finishes like the high solids conversion varnishes, remember that they are mostly "nonrepairable". While they sell great toughness and resistance to wear and tear, they will, eventually bow to the onslaught of 4 year old's coloring books and teenagers' soccer cleats. You then have a major job on your hands to refinish the piece, and you may wish you'd chosen the solvent lacquer that's oh so easy to renew.

Re: Cold Weather Finishing

#9

coloring books can be a problem with CV?


Re: Cold Weather Finishing

#10

Dale Lenz

Ron

Dale Lenz

Tried to email you twice and they both bounced back. My email: dalelenz4@gmail.com

Re: Cold Weather Finishing

#11

30 years experience

Bill Tindall, E.Tn.

I have used Sherwin Williams conversion varnish for 30+ years. I have it on house trim, stairs, kitchen cabinets, and furniture that will suffer from use like dining table, coffee table. I like that it can be washed. It has held up 22 years on stairs we use daily.

Because it is hard it sands easily. If I had to refinish something I would just sand it back to bare wood if the surface was flat.

Because it is cross linked it is insoluble in everything. This fact may sound like a bad thing for refinishing, but it is a good thing. It can be softened in a strong stripping solvent. If you strip lacquer or shellac you get snot that must be removed by successive solution/dilution with stripping solvent. With a cross linked finish like conventional varnish or conversion varnish the stripping solvent softens the film and it peels off in sheets....easily.

Re: Cold Weather Finishing

#12

Metaphorically Speaking

Mark Mandell - Gone Round In New Jersey

A 4yo can and will beat the snot out of any wood finish with of without crayons.

[don't be so "literal", Dick ;) ]

Re: Cold Weather Finishing

#13

Don't Disagree

Mark Mandell - Gone Round In New Jersey

my point was "repair" vs. "refinish".

Re: Cold Weather Finishing

#14

I'm with Bill on this one

Dick Coers

I just wondered what consumer testing agency used coloring books as a test, mustard, gin, and coloring books?

Conversion varnish is the perfect finish for a table as far as I am concerned. Of course you don't need any finish if you keep a dining table like my Grandmother did. 1/2" pad, base table cloth, then lace table cloth on top of that. When it was time to eat, we were at the steel kitchen table. It took a really special meal to put a useable table cloth on the dining room table and then eat there. Never saw the wood!

Re: Cold Weather Finishing

#15

Kitchen Cabinets as Well.

Mark Mandell - Gone Round In New Jersey

C-V will take the cleanings and probably outlast the doors and drawer fronts to the point that the next resident will simply remodel rather than repair or refinish.

MIL used pads like that all the time, cushioned and felt-backed to protect her dining table. FIL made special mica-laminated "kids" tables for coloring books and whatever.

Grandma had her living room couches and chairs "vacuum sealed" in 20 mil vinyl; soooooo comfortable in hot weather . . . :D

My point was simply that for some items, an easily repairable finish may be the better choice. Materials technology will continue to advance, probably to the point that the coating will outlast the wood on which its applied.

Re: Cold Weather Finishing

#16

Re: 30 years experience

TomD

Thanks Bill!

Re: Cold Weather Finishing

#17

Re: Conversion Finishes

TomD

Thanks Mark. I don't want to use the stuff on furniture, I don't like the look and plan for a much longer life span (with little optimism the future will be that kind). I have other projects in mind, and Bill is a good data point on what works and doesn't.