Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Pattern Routing Edge Joint

Posts

Pattern Routing Edge Joint

#1

Pattern Routing Edge Joint

don stephan

May be asked to glue together two slabs, too big and heavy to push through jointer. I've used before a straightedge and router to make a straight edge when the jointer wasn't an option. But in this case after making a straight edge on one slab I'd need to use that edge to pattern route a matching edge on the 2nd slab. Having never tried this before, why doesn't the router wildly run off when the bit is trapped between two edges? Thanks in advance.

Re: Pattern Routing Edge Joint

#2

Where is the Router Lady when we need her?

Barry Irby

I think this is "routing sympathetic Curves" and I have forgotten how.

Re: Pattern Routing Edge Joint

#3

Re: Pattern Routing Edge Joint

Dick Coers

Why would you want to do them both at the same time? The old Joint-A-Ability system was a piece of MDF with a square tube in the center. You would rout one board using the left side of the steel tube, and the other board on the right side. Complimentary cuts.

Re: Pattern Routing Edge Joint

#4

Re: Pattern Routing Edge Joint

John in NM

EDIT: Just thought about what I wrote - wouldn't work! :D

Does it have to be such a curve? Why not just cut it straight?

I would probably get out a hand plane and do it that way, or go borrow a buddy's 12" Oliver jointer - most of those big ones are sturdy enough to joint stuff you'd need a hoist to get on the bed :D

Re: Pattern Routing Edge Joint

#5

Bit More Info?

Mark Mandell - Gone Round In New Jersey

You wish to have two glue faces on the edges of 2 slabs to join them to double the width?

If this is correct, you can do this with a well-tuned table saw. Crude drawing shows how to get a straight edge on each piece of slab using the TS fence and a straight 2x4. Your work pieces get 2 small holes that are easily filled.


key is a well-tuned saw with a solid fence and the blade cutting at 90°

Re: Pattern Routing Edge Joint

#6

PS

Mark Mandell - Gone Round In New Jersey

You can eliminate an error in the blade angle by cutting one piece face up and the other face down. When flipped the 2 edges should match to a hairline.

Re: Pattern Routing Edge Joint

#7

Re: Pattern Routing Edge Joint

Mark Hennebury

Trim one piece at a time.

Using a straight edge clamped to the slab and set to trim about 1/16th" trim with the router using an upcut direction this will pull the router tight to the fence. go back to the starting position and move the second slab into the cut path about 1/16th" then pass the router along the straight edge again, this is a climb cut on the second slab this will push the router into the fence.

If you are actually going to cut a pattern edge you need to use one pattern and two bearing offsets to place the cut on opposite sides of the finish line.

Re: Pattern Routing Edge Joint

#8

Re: Where is the Router Lady when we need her? *LINK*

Jesse Cloud

Here's Carol's response from the last time this came up:


Router Lady

Re: Pattern Routing Edge Joint

#9

So?

Mark Mandell - Gone Round In New Jersey

How's the project going?

Re: Pattern Routing Edge Joint

#10

Re: To answer your actual question

TomD

It is a good question, there are some sneaky things that can happen...

1) So when doing cuts that cut both sides same time, you have balanced forces in line with the cut, the right side is pushing back and the left side is pushing in, and they net out. Unless you pushed two edges together that were uneven, where you could at some point be cutting heavier on one side than the other.

The lateral force is all to the right.

2) If you are using a template where you do a pass on one side, then the other, you need to feed each in the right way, or you could end up climb cutting.

3) not all climb cutting is bad, joinery wise you can make the final cuts with very slight cuts, these might be controllable in a climb direction, and it might yield a cleaner cut. This approach is used in some dovetail jigs where one scores the surfaces, then powers the waste. It is also the strategy things like table saw with secondary blades use. And many metal working machines.

There are also certain router cuts where climb cutting blows away material but never quite snugs up, leaving one to waste material quickly while always leaving a hair to be taken out in the self setting direction. An example of that is freehanding router pins, at least as far as the waste is concerned, in that case the precision is hand sawn.

Re: Pattern Routing Edge Joint

#11

Re: Pattern Routing Edge Joint

don stephan

Thanks everyone for your insights. At this point in the process I am making sure the customer understands just how involved it will be to make a 10' x 40" trestle dining table from three air dried pine slabs approx. 4" thick.