Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Re-assembling/lubricating table saw

Posts

Re-assembling/lubricating table saw

#1

Re-assembling/lubricating table saw

Tom Dunlap

My table saw is clean now. Nice to see the gears and ways all smooth.

Before reassembling the works I want to lubricate the mating surfaces. I'm inclined to use Johnson's Paste Wax. I could be convinced to use something else though.

Even though the Twin Cities are experiencing April weather in December my shop is unheated. The night temps are in the mid/upper 20's. This seems a bit cool to expect any paste wax to get into the saw parts. Should I just go ahead, rub wax in/on and call it good? It seems that if the iron were warmer the wax would penetrate better.

But...how warm?

Bring the parts in the house?

Slather on wax and melt it in using my hot air gun?

Put them in my oven at a low temp to warm up? There's no SWMBO in my house :( so I can get away with it ;)

Or...slather it on...rub it in and reassemble?

Tom

Re: Re-assembling/lubricating table saw

#2

Re: Re-assembling/lubricating table saw

John C Lucas

Put the wax in the house over night so it's warm and soft. That's what I did for my table saw recently and it worked fine

Re: Re-assembling/lubricating table saw

#3

Clint Searl

Re: Re-assembling/lubricating table saw

Clint Searl

Many years ago I got a quart can of a graphite paste lubricant that dries on application, and does not get sticky or attract dust. Very slick and lasts forever.

Re: Re-assembling/lubricating table saw

#4

Re: Re-assembling/lubricating table saw

Bruce, a MN Galoot

I don't know what parts you're talking about. Trunnions, gears? You could just heat them up a bit with a Harbor Fright heat gun.

Re: Re-assembling/lubricating table saw

#5

Re: Re-assembling/lubricating table saw

William Duffield

A couple other options:

Thin the wax with petroleum distilate (e.g., mineral spirits) before applying.

Add some carnauba wax or bees wax to the thinned wax, e.g., http://www.popularwoodworking.com/woodworking-blogs/chris-schwarz-blog/anarchists-2015-gift-guide-day-8-better-beeswax

Instead of wax, use PTFE, for example, http://www.popularwoodworking.com/woodworking-blogs/chris-schwarz-blog/anarchists-2015-gift-guide-day-4-blaster-dry-lube

The advantage of PTFE is that sawdust, etc., won't stick to it. The advantage of a harder wax (after the solvent evaporates) is that dust is much less likely to stick to it.

Re: Re-assembling/lubricating table saw

#6

ebd

Re: Re-assembling/lubricating table saw

ebd

+1 on Clint's solution. Or - get some dry spray lube at a mountian bike shop. Wax and other petro lubes will attract "crap" (sawdust, dirt, etc.) and eventually gum up everything.

Re: Re-assembling/lubricating table saw

#7

Re: Re-assembling/lubricating table saw

fredhargis

I've always used the paste wax (mine is Trewax, same thing) and it's worked very well.

Re: Re-assembling/lubricating table saw

#8

Table saw---solution *LINK*

Tom Dunlap

Today I did the last bits of cleanup on the saw. Just a little bit of surface rust to sand off.

Then I used my hot air gun to melt the last gobs of Johnson Paste wax from a vintage 1978 purchase. Enough for another couple of years I guess!

Wax went on all of the mating surfaces that I could reach. The pivots and shafts that I didn't dismantle needed a bit of lube. I remembered that I'd been using Liguid Teflon to keep my carabiners working smoothly. A bit went on the carriage pivots as well as the trunions and gears.

What a difference!

It took a little while to get the parts back together. Shimming the top was the next task.

The last was to bolt the cast iron wings on the top. They were high on the outside so I needed some shim stock. To save a trip to the hardware store I went in the house and grabbed a beer. It was time anyway :) Cutting the beer can into strips made for some excellent shim stock to level the wings. On the left I needed three thicknesses folded and tightened in above the bolts. The little tab that was above the table came off with a swipe of the box cutter. On the right I needed three thicknesses on two bolts and two on another.

Ready to cut up some wood for bookshelves tomorrow!

Tom


Liquid Teflon