Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Flooring question

Posts

Flooring question

#1

Flooring question

mdclor

Good morning to everyone,

I am installing natural pre-finished 3/4" maple flooring. What product is best for filling the face nail holes? DAP, Minwax, etc? Oil or water base?

TIA

Re: Flooring question

#2

Re: Flooring question

Ralph Lipeles

I thought that when installing tongue and groove flooring, the nails are put in at an angle through the tongue. Doing it that way there are not any visible nail holes.

Re: Flooring question

#3

I would .....

Brian Roberts

use a blind nailing procedure.

Either a commercially available unit like this:

http://www.leevalley.com/us/wood/page.aspx?c=&cat=1,41182&p=32683

Actually I used one of my carving gouges to lift a chip...leave it connected.....and experiment first on a scrap to get the hang of depth and angle of the tool.

Works quite well.

Re: Flooring question

#4

Not necessarily

David Yoho

You can't get the nailer oriented close to the wall so that strip has to be face nailed.

Re: Flooring question

#5

Re: Flooring question

mdclor

Ralph, David is correct that you can't use a flooring nailer close to walls, etc. Brian, the LV tool is no longer available. I could try the method, but I think it will be more time consuming and, personally, I find it to be intimidating/scary. :)

Re: Flooring question

#6

Re: Flooring question

Bruce, a MN Galoot

I just used my brad nailer and 2" brads. It leaves a very small hole and you can get very close to the baseboard.

Re: Flooring question

#7

Re: Flooring question

Mark Nowicki

Nothing.

The nail holes are small enough not to be visible, in many cases they end up being hidden under furniture or casing and shoe molding.

Some of the rows that the nailer can't reach can be hand nailed through the tongue. Drill an angled pilot hole and sink the heads with a nail set.

Re: Flooring question

#8

Re: Flooring question

George Koch

All I've ever used was colored putty of the correct shade, bought at the local paint or hardware store.

Re: Flooring question

#9

It doesn't matter

Bill Tindall, E.Tn.

As others have said the holes are off on the edge of the floor and will be unnoticed. I have used whatever filler I could handily find.

I don't recommend the brad nailer. I don' even like the ideal of finishing nails because they don't hold well. I have used the nails that are used in the flooring nailer.

These nails need to have good holding power. In my youth one could find flooring nails, a beefy finishing nail with a screw shank.

Re: Flooring question

#10

Re: Flooring question

mdclor

George, do you remember any particular brands that you were or were not happy with the results?

Re: Flooring question

#11

Re: Flooring question

mdclor

Mark, the last 2-3 rows are problematic because I am using 2.25" strips and even with drilling, I don't have enough room to swing a hammer.

Re: Flooring question

#12

Re: It doesn't matter

mdclor

Bill, I haven't seen those nails in a long time either, but even if I had them, I would want to sink them and fill the holes.

Re: Flooring question

#13

Re: Flooring question

Mark Nowicki

Use trim screws.

Re: Flooring question

#14

Re: Flooring question

Barry Irby

I like the trim screws.

For filler, I would use something water based, at least not oil based. In the past I used oil based putty under latex paint. The oil bled through. Probably woudl not happen with pre-finished flooring, but why take a chance?

Re: Flooring question

#15

Re: Flooring question

mdclor

Mark, am I missing something? Wouldn't trim screws need to be sunk and filled in above them?

Re: Flooring question

#16

Re: Flooring question

mdclor

Barry, thank you for answering one of my questions. Water base it is. :)

Re: Flooring question

#17

Re: Flooring question

George Koch

The brand I've been using is "Color Putty" from the Color Putty Co. made in Monroe WI. It is oil based but it doesn't matter because it's used after the sealer is applied and you said it was prefinished flooring. George

Re: Flooring question

#18

Re: Flooring question

Mark Nowicki

In my experience, I have only had to face nail the last strip.

Once the nailer runs out of room, I drill pilot holes and hand nail through the tongue until the last strip. You really don't need room for a full hammer swing, but you said you don't have, or feel you don't have room for that.

You need less room for a screwdriver, power or hand, hence my trim screw suggestion.

On a 2 1/2" strip floor I would just glue the last strip and not bother nailing, if appearance is a concern.

Another option is to glue up the last couple of strips, and just face nail through the last strip.

I have done that on a few occasions.