Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

walker turner motor issue

Posts

walker turner motor issue

#1

walker turner motor issue

anthony siciliano

I have a Walker Turner Model 1100 Radial Saw, and have had it for many years-although I never used it due to space constraints. It has always been indoors in my shop and although dusty it was always warm and dry. Lately, I decided to sell it and plugged it in to be sure it was functioning, meaning the motor spun. It does spin, for about 2 second, before it pops it's breaker-20amps/110 volts (it has a switch that supposedly transfigures it to 220V mode but I never tried that either) I don't remember ever having the breaker issue so not knowing much about electic motors or capacitors etc, I am at a bit of a loss. I know asking for long distance trouble shooting is fraught with complication but figure I'd start somewhere. Any help will be appreciated. The idea of removing the motor and lugging it (probably weighs a 100 pounds) to a shop 30 miles from here isn't all that appealing. So thanks in advance and thanks for looking.

Re: walker turner motor issue

#2

Re: walker turner motor issue

Dick Coers

How long has it been sitting unused? Does it spin freely by hand? Did you try starting it without the blade? I'm thinking the bearings are gummed up, or the starting method is frozen. No idea if it has a start capacitor or centrifugal start switch.

Re: walker turner motor issue

#3

Re: walker turner motor issue

anthony siciliano

It has been sitting for ages, maybe 25 years, I'm almost ashamed to say. It does turn freely, I have a 12" blade on it that I had made at Connecticut Saw that has never cut anything except me when I got to close (not running at the time fortunately). There is a "rotating switch" on the end of the motor that is exposed because the cover for that is missing. There is also, what I believe is a capacitor, a big gray cylinder attached to the motor with a wire running from it which either goes to the motor or the switch box? Can't remember just now, saw is in the shop. Gummed bearings I could deal with, I might have said the environment is/has been definitely dusty. Thanks for your response.

Re: walker turner motor issue

#4

Re: walker turner motor issue

Bill Turpin in WNC mountains

There is a start switch in motor end away from the blade. Have you blown the dust out of this open end. This switch needs to open after or during startup. You should hear a definite CLICK during startup. This takes out the starting circuit and reduces the amperage allowing Cbreaker to stay on. The grey capacitor should be a symmetrical oval. If it is swelled it is bad due to overheating its oil inside.

Re: walker turner motor issue

#5

Re: walker turner motor issue

hairyapple

The capacitor seems okay, not obviously swollen. I'm leaning toward the impacted with dust theory as what else could really change as the saw has just stayed in one place, a silent sentinel to early wood working machinery. But the dust is ever present. We clean out the shop occasionally by the following method, which could impact the saw's operation. First we put away anything that could fly around. Then we raise the one overhead door then bring it back down onto a whole house fan. The balance of the opening is filled with plywood. At the diametrically opposed end of the shop we just open the passage door and brace it in that position. Then we don our 3M face masks with organic filters. One of us in the loft and one on the ground floor but both armed with back pack blowers. Start the blowers, turn on the overhead fan and monster dust removal fan that I built in between the loft's trusses. Then just start to dislodge the dust that has settled everywhere since the last cleaning. We keep the dust airborne until it can pass out thru the whole house fan. The shop is 24 x 36 feet with an open loft about 2/3 that size. It takes 30 to 45 minutes of constantly blowing the dust back up to clear it all out. Credit for this idea goes to Marc Rich late of Astascadero, Ca who was my one time partner and best friend. Before we had the whole house fan we'd line up 5 box fans that we found at the dump, that worked too. So years ago I was working at a hobby company and we rented space to a German company that made packaging machinery. 2 German engineers came and they set up a number of machines for display and to show how they functioned. They were full functional machines that folded cartons at the rate of 5,000 an hour. They told me that in Germany one would never blow degri off of a machine like this as it would only tend to impact same with dust etc. They only ever vacuumed when things needed cleaning. Maybe I should have paid better attention.

Re: walker turner motor issue

#6

Re: walker turner motor issue

Waltz

Please be clear is the circuit breaker a GFIC / ground fault breaker?

Will you Please try a direrent 20 amp circuit.

We will give you very different advise if you are using a GFIC circuit.

A weak, overloaded circuit or a long extenion cord could produce your symptoms.

Walta

Re: walker turner motor issue

#7

Re: walker turner motor issue

Bill Turpin in WNC mountains

There is a centrifugal weight that has to move depending on motor speed. Away from rotor while running, near the rotor while stopped. As speed increases it opens the switch contacts. Burned, dirty contacts or welded stuck contacts could cause your problem. One problem does not allow for start winding, the other allows it to be energized too long. Too much dust does not allow the weight to move. Make scratch marks on BOTH end bells and the motor body. Remove the four bolts and remove the back end bell. Clean out all the internal nastiness. If any wires are removed take a cell phone pic first. Clean and/or unstick contacts. Reassemble. Tighten bolts until nuts just touch. Using nut drivers(for ease of use) slowly tighten bolts a little at a time WHILE spinning the armature. Continually spinning the shaft tighten the bolts until snug. Make scratch marks with a scratch awl, pass it across the mating of the end bell with the body. Use one mark at the front and two parallel marks at the other end. This allows perfect alighnment of thru holes in body with holes in the end bells.

Re: walker turner motor issue

#8

Re: walker turner motor issue

anthony siciliano

Thanks for your response. Not GFIC breaker, there is a short extension 12 gauge extension. I used it to try other 20 amp breakers, all led to same result. My shop, which is in a barn like building on my property has it's own 200amp service. I wired the barn myself after an electrician erroneously installed the meter box. Figured I could do mess it up myself for free.