Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

mounting doors to face frame

Posts

mounting doors to face frame

#1

mounting doors to face frame

BillP

My shop had very little storage just an old homemade bench and some shelves. I thought I'd give cabinets a try and made a corner set 6 foot in each direction. I'm to the point of mounting the doors. The opening is 15" x 19 1/4" and the door is 15 1/2" x 19 3/4". I am using a self-closing hinge with a 1/4" overlay. When I mounted the door, the up and down is centered but the left to right is shifted to the left about a 1/16 of an inch. I've never done anything like this so I'm really not sure what to do. I know it's just cabinets in my shop but it drives my crazy when I see it. I am wondering if the hinges are to be recessed on the face frame side to center up the door.

Thanks, Bill

Re: mounting doors to face frame

#2

Re: mounting doors to face frame

don stephan

the answer might depend in part on the type of hinge - European, barrel, . . .

Re: mounting doors to face frame

#3

Re: mounting doors to face frame

BillP

they are non-European.

Re: mounting doors to face frame

#4

Re: mounting doors to face frame

Richard McComas

OK they're not European. Your going to have to be more specific. There are many many different hinges out there.

The best, would be to post a picture or a link to a site that has the hinge you're using. Give us some more help.

Re: mounting doors to face frame

#5

Re: mounting doors to face frame

BillP

I don't know how to post pictures, not a member of any photo sharing sites. Here's the description from the Home Depot site.

Liberty

Model # H01911C-SN-O

Internet # 202066916

Store SKU # 565115

2-3/8 in. x 2-3/4 in. Satin Nickel 1/4 in. Semi-Wrap Overlay Hinge (2-Pack)

Re: mounting doors to face frame

#6

Re: mounting doors to face frame *LINK*

John McGaw

Looking at a picture of the hinge, it appears to be adjustable in the left-right direction. Have you adjusted it or have you adjusted it and run out of range?


The Hinge In Question?

Re: mounting doors to face frame

#7

Ellis Walentine

Re: mounting doors to face frame

Ellis Walentine

I am wondering if the hinges are to be recessed on the face frame side to center up the door.

If that will center the door, then, yes, that would be the thing to do. It sounds like you could do it in a few minutes time with a sharp chisel or a laminate trimmer with a straight bit.

Ellis Walentine, Host

Re: mounting doors to face frame

#8

Re: mounting doors to face frame

Richard McComas

http://www.libertyhardware.com/functional-cabinet-hinges/liberty-14-semi-wrap-overlay-hinge-h01911c-sn-o.htm

Very near the bottom of this web page it says "installation instructions: click here".

Re: mounting doors to face frame

#9

Re: mounting doors to face frame

John McGaw

Pretty poor generic instructions which the maker uses for a multitude of products. Problem is that some of the hinges have both vertical and horizontal adjustment and others don't. I suspect that OP might have the hinges without the horizontal slots otherwise he probably would have tried them first.

Re: mounting doors to face frame

#10

Re: mounting doors to face frame

BillP

If I could post a photo it would be much easier. The hinges are slotted in both directions and can be adjusted +/- 1/4" in all directions from the center of the slots. The problem is I have the hinge mounted tight against the door frame. So as Ellis suggested I will have to mortis them into the face frame to get the 1/16" I need. I just figured a 1/4" overlay would be just that. Well at least it was a cheap amateur lesson learned.

Thanks to everyone.

Re: mounting doors to face frame

#11

Re: mounting doors to face frame

Richard McComas

When in doubt build a mock up and work it out. Least that's what I do.

Re: mounting doors to face frame

#12

Re: mounting doors to face frame

John McGaw

Maybe I'm just being dense but, if your hinges do have horizontal adjustment, why can't you just make up the required difference by sliding the door on the hinges until the fit is satisfactory?

Re: mounting doors to face frame

#13

Re: mounting doors to face frame

BillP

There is plenty of horizontal adjustment to the left but it's maxed out to the right.

Bill

Re: mounting doors to face frame

#14

Re: mounting doors to face frame

Bill P.


I think I got the photo upload thing going, I knew I could do it before, DUH. This is from the first one I test fitted. It's for the shop so everything will be painted.

Re: mounting doors to face frame

#15

Re: mounting doors to face frame

John McGaw

OK. Looking at the picture clarifies what is going on. Yes, you could mortise the body of the hinge into the cabinet. However, if you want to save the trouble and you are indeed worried about a 1/16" offset of the door, you could just run the left and right edges through the jointer and remove 1/32" from each and then slide the door over. That should equalize the overhang on each side and I doubt that anybody will notice that your overlay is not precisely 1/4". If anybody approaches your doors with a precision rule, give them a whack and relax.