Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

JET JJ-6OS Jointer dust collection

Posts

JET JJ-6OS Jointer dust collection

#1

JET JJ-6OS Jointer dust collection

ChuckInND

About a week ago or so I bought a used JET JJ-6OS open stand 6" jointer. The way that JET positioned the dust port into the floor of the dust chute doesn't seem too efficient to me, so I decided to redesign and fabricate a new top for the dust chute. This is a link to the original JET setup. http://www.amazon.com/708455-4-Horsepower-Jointer-230-Volt-1-Phase/dp/B00064NGRY/ref=cm_cr_pr_pb_t Next is a link to my dust collection webpage that shows my solution. https://sites.google.com/site/deltacontractorstablesaw/

Re: JET JJ-6OS Jointer dust collection

#2

Re: JET JJ-6OS Jointer dust collection

William Duffield

The original JET setup can be more clearly shown in this parts diagram:

http://www.ereplacementparts.com/jet-jsl6j-open-stand-jointer-parts-c-32652_32674_288538.html

Probably there is a clearer copy of the same diagram on JET's site, but this one was easier to find.

I think Chuck replaced parts numbered 8 and 24 with his setup.

Chuck, Does it work any better than the stock setup? I suspect it does.

Re: JET JJ-6OS Jointer dust collection

#3

Re: JET JJ-6OS Jointer dust collection

ChuckInND

Hi William, your correct about which parts I no longer need. The jointer came with the chute top cover part number 8, the port number 24 was missing. I just bought the Jointer very recently and since it didn't have the port I never had a chance to hook it up to a dust collector. But with only the chute cover on I noticed that the opening was about 4" or 5" tall, the width is about 7". But looks are deceiving, at the top of the opening the chute cover was only about 1 & 3/4" away from the floor of the chute. Plus I didn't like the direction that the port was pointed, almost directly towards the bottom floor of the chute. And if you'd hook up a DC hose to it the hose would be directed slightly upwards. In a nut shell I wanted the port pointed in the same direction that the chute is. I can't imagine that this new setup wouldn't be better, the way that JET has it setup it looks to me like there would be some unnecessary air resistance. I noticed that Delta made a similar open stand jointer that could benefit from this also. And who knows how many other jointers, I think that both the JET and the Delta were imported.

Re: JET JJ-6OS Jointer dust collection

#4

Re: JET JJ-6OS Jointer dust collection

ChuckInND

William, the link that I posted to a picture of the jointer in Amazon actually shows the position of the port better then your link to the parts. If you can't see it that well in Amazon, then click on the picture to enlarge it.

Re: JET JJ-6OS Jointer dust collection

#5

Re: JET JJ-6OS Jointer dust collection

William Duffield

I agree, but I really needed both the picture and the parts diagram to understand the problems, and how you fixed them. The stock dust chute is about as flat as a pancake, and the air and chips have to take a very drastic turn to enter the fitting to the ductwork. This drastically slows the transport, which is made even worse by the need to fight gravity once in the duct. Your solution, enlarging the chute and taking the kink out of it, makes perfect sense.

Re: JET JJ-6OS Jointer dust collection

#6

Re: JET JJ-6OS Jointer dust collection

ChuckInND

Thankyou William, I put ALOT of time into designing and fabrication for it to be efficient and look good, plus without modifying the chute, and making it fairly easy to remove like the original chute cover. I fabricated it out of a fairly heavy sheet metal and painted it to match the machine. In my opinion even the older JET closed stand Jointers could benefit from a similar repositioning of the dust port. If I had one available I'd design and fabricate something for that also.

Re: JET JJ-6OS Jointer dust collection

#7

Re: JET JJ-6OS Jointer dust collection

David Bair

You will end up having to deal with all the gaps between the jointer proper and the stand (to which the dust collection parts are attached). These gaps need to be sealed if you're going to create enough suction to capture the bulk of the actual dust as opposed to chips. Otherwise, the dust will end up coating the infeed table and your glasses.

I replaced my three-blade cutterhead with a spiral cutter. If you need a replacement head, spare knives or bearings, you can have them for the cost of shipping.

Re: JET JJ-6OS Jointer dust collection

#8

Re: JET JJ-6OS Jointer dust collection

ChuckInND

David, that is awfully kind of you to offer that, and I appreciate it. The jointer that I bought appears to be in pretty nice condition. I will keep your offer in mind once I get a chance to use it, which maybe a while. The winters up here in North Dakota are bad enough to make a guy like me thats getting up in age want to hibernate. As far as the dust collection, I've always believed that a guy doesn't want to seal up a machine too much, it's got to get air in from somewhere. I use a 1 & 1/2 hp dust collector one machine at a time with a 4 inch dc hose.

Re: JET JJ-6OS Jointer dust collection

#9

Re: JET JJ-6OS Jointer dust collection

ChuckInND

I'll also add that I think that some folks expect that good dust collection is going to capture every spec of dust from every machine, in my opinion I think that is unrealistic. When I designed this dust hood I did look inside the jointer to see what the situation was. On the new chute cover I did add a little more to the top then what the original cover had, which should help divert more dust into chute. My basic goal in dust collection is to get it as good as I can without going over board. The reason that I have dust collection is less fine dust settling on everything, less piles of dust to walk through and spread around, and less cleanup time at the end of the day. If I'm concerned about my health I have a dust mask and an air filtration unit that eventually clears the air.

Re: JET JJ-6OS Jointer dust collection

#10

Re: JET JJ-6OS Jointer dust collection

ChuckInND

About a week ago I decided to redo the first dust hood a little to get rid of the square box look, plus it probably made it just a hair more efficient. https://sites.google.com/site/deltacontractorstablesaw/home

Re: JET JJ-6OS Jointer dust collection

#11

Looks Good, Chuck

Mark Mandell - Gone Round In New Jersey

I made a similar hood for my jointer. The 13" planer/molder came with a good dust hood.

I'd suggest you fashion an over-the-blade dust hood to control dust on the saw; it will help a lot. A friend with a contractor saw like yours hung strips of rubber roofing scraps to kind of close up the back of his saw. He says it helped the drop chute under the saw get more dust and keep stuff from blowing out the open back of the saw box.

Re: JET JJ-6OS Jointer dust collection

#12

Re: Looks Good, Chuck

ChuckInND

Mark, I'm no stranger to dust collection, I've been at it for about 10 years. Some people think that you have to seal up a piece of machinery in order to get good dust collection. And some think that you need a expensive .5 micron pleated cartridge filter. I'm not a believer of either. I'm very happy and proud of the DC setup that I have put together for the machines that I have. I have put a lot of thought into every one of them to make them work efficiently, and do it in a proffessional looking manner, and without butchering a piece of machinery to do it.

Re: JET JJ-6OS Jointer dust collection

#13

Then

Mark Mandell - Gone Round In New Jersey

stay happy and proud with what you've done and what you believe, Chuck.

I wasn't criticizing the work you've shown, merely passing along a bit of what I've learned and done over the last 25 years.

Re: JET JJ-6OS Jointer dust collection

#14

Re: Then

ChuckInND

Mark, there is a lot of BS out there. People that insinuate that dust collection is for health reasons is unreasonable. Buy a good dust mask if your concerned about breathing dust. Good dust collection to me will never be more then less dust settling on everything in the shop, less cleanup time, and the sooner that I can remove the dust mask. As far as materials that I use to make the dust hoods, I use a fairly heavy gauge sheet metal.

Re: JET JJ-6OS Jointer dust collection

#15

Re: Then

ChuckInND

I'll also add that I've been a woodworker for about 30 years, I've seen a lot of dust collection work out there, especially the HF dust collector mods and how popular it is. So they go and spend $150 - $200 for the cheapest made DC on the planet, then spend close to another $200 into a filter, and who knows how much time reconfiguring the DC in a manner where the blower motor now is in a vertical position. I have some doubt as to if the bearings in the motor will survive that side load for very long. The DC that I have I bought new for about the same price as the HF + cartridge filter. It was made by a once reputable company, so it should be a decent machine that should last for years, and it came with a good low micron filter. Plus the setup of the DC I didn't have to spend a bunch of time reconfiguring the it to make an onboard separator fit. It really boggles my mind as to why the HF is that popular when in my opinion there is a better option out there. While I'm at it and speaking of BS, I'm not a big believer that everyone needs a cabinet saw to do good work. But it seems that if you want to be takin seriously you must own one.

Re: JET JJ-6OS Jointer dust collection

#16

In That Case

Mark Mandell - Gone Round In New Jersey

I'll suggest you upgrade your system as what you have now is unable to get that chip you seem to have stuck on your shoulder.

I make a simple, friendly suggestion and you go off on some lecture purporting to criticize me when you have no idea of how my shop is set up or runs, and launch into some rant about Harbor Freight that has absolutely nothing to do with what I said.

I have no interest in being your straight-man, Chuck. Pick a fight with someone else, please.

Re: JET JJ-6OS Jointer dust collection

#17

Re: In That Case

ChuckInND

How is anyone suppose to react when someone comes along and says, yeah I built one of those hoods too, and acts like it's no big deal. Then they insinuate that someone else did a better job at dust collection then you did on your table saw. And now you want to make me look like the bad guy because I explained how frustrating things are because of all the misinformation out there ? Thanks.

Re: JET JJ-6OS Jointer dust collection

#18

Re: As far as the table saw goes

ChuckInND

Mark, I have never liked over the blade dust collection. I don't want anything in my way and or line of site when cutting. In my webpage I describe how the dust collection for my table saw works. I partially blocked off the open back, which includes blocking it off behind the blade, which moves with the blade so the dust can't can get thrown out the back. All the other areas of the saw that were open are now closed, so now all the air needed to feed the dust collector now comes in from the back, making it even less likely for the dust to escape. With your buddies rubber flaps there isn't anything below the motor mount to keep the dust from being thrown out under it at anytime, 90 degree cuts or beveled cuts. In my opinion it's less efficient. You may not believe me, but I've had my saw setup for dust collection for several years already. It works very well, and I'm completely happy with it. It took me a few days to figure out how to make it all work, it wasn't just some hour long afternoon project.