Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Making precise measurements/cuts

Posts

Making precise measurements/cuts

#1

Making precise measurements/cuts

Jesse Cloud

I had an "Ahah!" moment in the shop this afternoon and thought the idea might be useful to others. It worked well for me.

I had backed myself into a situation where I needed to remove exactly 0.06 inches from each side of a 30 inch panel. Yes, I know, not getting into this situation in the first place would have been the smart thing, but ....

I've been using an old deck of playing cards for shims for years. Well, I took my best caliper, set it to 0.06 inches, and locked it. Then I stuck playing cards into the cap until I had enough for a snug fit. It was five, but thats not generalizable.

So I set my tablesaw fence to the original size (by placing the board between the blade and the fence), the clamped a board to the table, snug against the far side of the fence.

Loosen the fence, insert the cards between fence and clamped board, snug up fence and make the cut.

For the next 0.06 inches, take the cards out, snug up the board, clamp and repeat the process above.

The cut worked beautifully. exactly 0.12 inches removed and the centerline is still the center.

I thought about adding this to the 1/64th markings on a ruler thread, but it was already awfully long.

Re: Making precise measurements/cuts

#2

Re: Making precise measurements/cuts

John K Jordan

Nice! Playing card shims! I use feeler gauges for shims on my milling machine but they wouldn't work too well on the table saw.

JKJ

Re: Making precise measurements/cuts

#3

Re: Making precise measurements/cuts

Steve Elliott

I use feeler gauges for accurate cuts on both the tablesaw fence and with a stop block for length cuts. It makes adjusting the cut by two or three thousandths quick and reliable.

Re: Making precise measurements/cuts

#4

Slick!!!  Thanks.


Re: Making precise measurements/cuts

#5

Re: Making precise measurements/cuts

Jim Dillon

Jesse, I've also used the old playing card trick as shims for years in TS jigs to achieve much the same thing as you describe for the TS fence. I've also used them under chisels to avoid marring the underlying surface as well as under flush-cut saws for the same reason. Thanks for the tip on yet another use for such a handy shop "accessory". Jim

Re: Making precise measurements/cuts

#7

Kent B

Future Reference:  Hotel Key Cards are 0.030 "

Kent B

I have a bunch of them, collected over the years when I traveled relentlessly for work.

Thirty thou. Close enough to 1/32".

Playing cards are cool, too.

Also, turns out that for 15 years, my business cards were wood veneer, and they vary in thickness with species, but 12 - 15 thou is common. Plus, being wood - they glue just fine, as in, shimming a thin tenon.

Re: Making precise measurements/cuts

#8

Shims

Bill Tindall, E.Tn.

I keep a collection of pieces of plastic used to wrap items for sale in stores (that tough transparent stuff that one risks slashing injury trying to extract the item ) and motel key cards. Shims come in handy on many occasions. The shims are stored near the table saw so I supp9osie it means that is where I used them the most.

Re: Making precise measurements/cuts

#9

shooting board

Bill Tindall, E.Tn.

This comment is drifting afield, but for removing smidgens of wood I find a shooting board "safe". The advantage, and disadvantage, of power tools is that wood goes away quickly and two smidgens go away in the blink of an eye.

Re: Making precise measurements/cuts

#10

Re: Shims

Barry Irby

I have made a number of tables With three legs attached to a central turned column. Used a sliding dovetail. Not being a handtool guy, I set up a router on the lathe to cut the DT slots, using the indexing feature on the lathe to get them equally spaced. While at the same set up, I cut a small flat on the spindle to avoid having to undercut the shoulders on the legs. I cut the DT's with a very slight taper, wider at the bottom and narrower at the top. Then I use a bit with the same angle to cut the matching DT on the legs at the router table. To get the taper on the DT on the legs, I put Three of four thicknesses of tape on each side at the "thicker" end or bottom. It amazing how that tiny bit of taper makes the legs slide home and lock up tight at the last half an inch. If necessary, I remove a piece of tape from one side or the other or both to make the DT just enough thinner to slide home.

Blue tape makes great very thin shims. I also use key cards. They also make great glue spreaders.