Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Old table fix - some questions

Posts

Old table fix - some questions

#1

Old table fix - some questions

Joe in a Cleveland suburb

Hi all.

My wife picked up this enamelware table from an antique shop a couple weeks ago in VA. She asked me to fix it. Yes dear...

I was wondering if some of you might have some suggestions/advice with the following questions. I know, don't say throw it away. :)

I need to replace the wood pieces the hinges are screwed into. On both the top and leaves. I may as well replace all the wood pieces with poplar.

The wood pieces all seem to be simply held in place by friction. Any idea how they manufactured these tables? Or when? 40's?

All the wood pieces are T&G. They seemed to have been simply smashed into place. The metal top has rolled edges that the wood pieces fit under.

Any suggestions on a better way to do it?

I am thinking of simply putting the horizontal pieces in place, then cutting the cross member to fit snug, and use pocket hole screws to hold

it together.

I'll make a new simple base and legs from poplar. Maybe. Maybe I'll just tell her to paint it...

Thanks for any info.

#1


#2


#3


#4


#5


#6


Re: Old table fix - some questions

#2

Re: Old table fix - some questions

John K Jordan

I bet a good antique dealer could tell you when this was made.

From the clearance corners cut from the cross pieces and the small support blocks it appears to me a clever way to wedge the frame tightly into the steel rim before stapling. Seems to me that duplicating the T&Gs would keep things straight and sturdy and "restored." Maybe a wood stronger than poplar for where the hinges attach?

Re: Old table fix - some questions

#3

Re: Old table fix - a recommendation

Ralph Lipeles

Can you rotate the sections 180 degrees to expose undamaged wood for the hinge screws? You might have to run the boards through a table saw to recut the grooves for the cross pieces. Also, the wood has probably shrunk over the years. You might want to dry fit, measure, and make spacers to go between the wood and the metal top to keep things tight.

Re: Old table fix - some questions

#4

Kneale Brownson

Try butterfly/bowtie fixes for screwhole wood?


Re: Old table fix - some questions

#5

Re: Old table fix - some questions

David Yoho

What's interesting to me are the center pieces in pictures #1 & #6 where they have the dog-eared cuts on opposite ends. I wonder if they were installed after the other parts were to sort of "stretch" the whole thing snug under and against the rim. Given the space to insert them afterwards, the dog-eared cuts would allow them to angle and fit these parts into place while tapping them home. Otherwise, I can't see why those parts are cut like that.

Poplar would be an economical solution but I don't think it would hold the screws as well as another wood choice. It looks like pine was used originally in the pictures, which would make sense for the time. Another choice that wouldn't be out of keeping with the time it was built might be oak.

Pocket hole joinery would be quicker but why not go with what they used - tongue and groove?

While you probably aren't looking to do a historical restoration here but a "fix it the simplest way and move on" approach, it wouldn't hurt to take a little more time and effort with your repair.

Re: Old table fix - some questions

#6

Re: Old table fix - some questions

Joe in a Cleveland suburb

"What's interesting to me are the center pieces in pictures #1 & #6 where they have the dog-eared cuts on opposite ends. I wonder if they were installed after the other parts were to sort of "stretch" the whole thing snug under and against the rim. Given the space to insert them afterwards, the dog-eared cuts would allow them to angle and fit these parts into place while tapping them home. Otherwise, I can't see why those parts are cut like that."

That's what I figured as well.

"Poplar would be an economical solution but I don't think it would hold the screws as well as another wood choice. It looks like pine was used originally in the pictures, which would make sense for the time. Another choice that wouldn't be out of keeping with the time it was built might be oak."

I agree with you and the others. Oak or maybe Maple. I'll have to see which is cheaper at the local WoodCraft. I hate buying wood at WoodCraft but I no longer have a vehicle I can drive to the Amish mill/kiln where I used to get wood and load up. :(

"Pocket hole joinery would be quicker but why not go with what they used - tongue and groove?"

I don't really want to put the time and effort into this.

Thanks all for the replies. I have some better ideas now.

Re: Old table fix - some questions

#7

Re: Old table fix - some questions

Greg

You could try keeping the original wood, but replacing the wood screws with tee nuts and machine screws. It looks like the original wood is strong enough. I have included a link to tee nuts, but you should be able to get them in most hardware stores.

http://www.amazon.com/gp/product/B000H61YF2?keywords=tee%20nuts&qid=1446075967&ref_=sr_1_1&s=hi&sr=1-1