Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

dust collectors

Posts

dust collectors

#1

dust collectors

BillP

I searched the site for suggestions but I only found ones that were old. I have an AP400 1 HP Delta it's at least 6 or 7 years old. Tonight I used it while ripping 3 boards, then went to plane them but when I turned it on it would only hum. I checked for replacement parts and the ones I think I need are not available any longer. The motor turns freely. The question is, fix or replace. If I should replace it to a 11/2 HP what are some good choices.

Thanks Bill

Re: dust collectors

#2

Re: dust collectors

Dick Coers

Make sure the impeller isn't stuck from debri. If clear, make sure it spins freely. Then get the info off the start capacitor and order a new one from someplace like Graingers.

Re: dust collectors

#3

Re: dust collectors

Bill Tindall, E.Tn.

I set the bar for frugal, yet sprung for a 1.5 hp Oneida system. After living with it for a while I wonder why I didn't buy it years earlier. I do a lot of woodworking so for me it became good value. Used less it might not.

Re: dust collectors

#4

Re: dust collectors

Barry Irby

My Delta DC is at least that old and I have forgotten the specs on the motor but as I recall its a 1 1/2hp and it one of the enclosed or sealed motors.

Check your motor and if its one of the fan cooled open designs blow it out with compressed air. It may also have a centrifugal switch built into one end of the motor. Blow any dust out of that. (Mine is outside the shop and not subject to the dust.)

I ran mine for a very long period the other day and for the first time the thermal over load switch tripped. I let it cool down, pressed the button and it went back to work. But, with the switch tripped, it did not even hum.

Beyond that, I agree the capacitor is the likely culprit.

Re: dust collectors

#5

Yep, capacitor.... *LINK*

John in NM

Could be a blocked fan or switch, as Dick and Barry have suggested checking, but odds are its a dead cap as they go on to point out.

You can order caps from Grainger or McMaster, as well as many other vendors. Start capacitors are typically in the 50 to 100 uF range, though for small motors you may see them lower than that. As long as it's large enough, the acceptable range is not overly specific. Run capacitors are specific in value to withing 5% or so usually.


Motors and capacitors

Re: dust collectors

#6

Re: dust collectors

ChuckInND

About 5 years ago or so I bought a new Delta 50-760 dust collector. It is a 1 & 1/2 hp unit, with a 5 micron felt bag. I chose the unit for it's design, which I was easily able to add a onboard separator too. Now mine is considered as a two stage unit. My shop is also our 2 stall garage that we also park our vehicles in. It's been a great setup for me, and at a very reasonable cost considering what most 1 & 1/2 hp 2 stage DC's go for. Delta no longer makes the 50-760, but perhaps you could find a new old stock by chance, or a used one. I really like the one that I have, and feel that it's the best bang for the buck in a 1 & 1/2 hp DC.https://sites.google.com/site/deltacontractorstablesaw/

Re: dust collectors

#7

Re: Yep, capacitor....

BillP

Thanks for everyone's help. I took the cover off the switch last night. I found a white capacitor about the size and length of 2 "D" cell batteries. Near the top it looks like it melted inside and is bulged out. I will take that to the local electrical supply store to see what they can do for me.

Re: dust collectors

#8

Re: dust collectors

BillP

They didn't have the exact one but one slightly larger. I hooked it up and hit the power and presto it ran. It was short lived though, after about 7 or 8 minutes run time ..... POP! A little puff of smoke and some liquid running out the housing and that was it. I guess this one is better left to the pros.

Re: dust collectors

#9

Re: dust collectors

John in NM

That sounds like the switch that disengages the start cap is stuck closed. Start caps will do exactly what you described if used as run caps.

You might be able to repair it with some motor dis-assembly, hard to say. Those centrifugal switches are not usually a serviceable item.

Re: dust collectors

#10

Come to think of it....

John in NM

My first table saw had a separate switch for the cap, probably for this very reason. To turn it on, one would flip both switches up at once but the cap switch was momentary contact so would break the connection as soon as you let go.

Cheap fix.

Re: dust collectors

#11

Re: dust collectors

Bill Howatt

I'd take it to a motor shop, they likely will have a switch that will fit if necessary.

If the motor isn't a Totally Enclosed Fan Cooled (TEFC) motor then it may have a build up of sawdust and dirt inside that is interfering with the centrifugal switch - a good cleaning or even a blow-out with compressed air might correct the problem. I admit that dust and dirt usually causes the switch not to close rather than not to open but...

Bill

Re: dust collectors

#12

Only thing is....

John in NM

Last time I took a motor around it was getting very hard to find shops willing to work on small single phase motors. I got the impression that if the bill wasn't going to be $500 or more, the didn't want to do it.

Could have just been the city (Tucson) rather than a general trend, so it would be worth a try.

Re: dust collectors

#13

Re: Only thing is....

BillP

Yeah, I googled shops and of the 2 within 20 miles, one was out of business and no answer at the other.

Re: dust collectors

#14

Re: dust collectors

BillP

Ok, if the cost to repair is more than it's worth which one of these would you prefer. Powermatic PM1300TX 1.75hp with 30 micron bag or Jet DC 1100VX-5M 1.5hp with a 5 micron bag. I don't have any experience with either brand. They are at about the limit I want to spend if need be.

Re: dust collectors

#15

Re: dust collectors

John in NM

I would do the two switch solution I mentioned.

Failing that, I would probably replace the motor. Price ranges are anywhere from $150 on up depending on quality. Bargain basement are the Chinese motors that HF sells, maybe $100 more for a Leeson from Northern Tool.

Re: dust collectors

#16

order cap on-line?

John K Jordan

Amazon.com has a variety of starting capacitors, some Prime for 2-day delivery if you have that service. (I use Amazon a lot since it is easy. I get lots of supplies like electrical, glue, power and hand tools, even bought a heavy-duty Jet metal-cutting horizontal/vertical bandsaw with hydraulic advance. The prices are often competitive.)

They will even send you the Powermatic 1300TX you mentioned. (I know nothing about those; I installed a 5hp ClearVue cyclone in my shop.)

You can probably get the specs for the capacitor from the old one you removed.

JKJ

Re: dust collectors

#17

stay away from 30 micron bags

Neal in San Jose

According to the Bill Pentz site and other authorities I've read, the dust that is most harmful to lungs is below 30 microns. A dust collector with a 30 micron bag is recirculating the most harmful sizes of particles and doing more harm than good.

Re: dust collectors

#18

This was my thought, too.

Barry Irby

It's the 'fines' that are going to get you and don't settle out as readily as the course stuff.