Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Spilt glue line reapir

Posts

Spilt glue line reapir

#1

Spilt glue line reapir

Dustmaker Mike

Well about 11 or so years ago I made my daughter a cutting board in the shape of Winni the Pooh. She had been using it but not really taken care of it. I think one of the grand kids put it in the dishwasher. She gave it to me to fix it. The wood is really dry which I can fix pretty easy. The problem is the two splits along the edge joined wood. They are about 4 or 5 inches long. I was wondering how I can finish splitting it along the glue line so I can reclean the edge and reglue it with out loosing the shape of the overall board.

So I was thinking of using a large knife like a wedge and finish the split. Before I go and destroy it I wanted a sanity check.

Will this idea work?

Re: Spilt glue line reapir

#2

Re: Spilt glue line reapir

Dick Coers

You'll be able to clean the joint if you split it apart, but you won't get any better glue joint than you have now. I'd flip one half and clamp it to the other piece. Then a few strokes with a hand plane to make a good joint.

Re: Spilt glue line reapir

#3

Re: Spilt glue line reapir

don stephan

I'm not confident the split will continue along the glue line - it might, and it might not. If it doesn't I would expect the repair would be more difficult. As an alternative you can saw the full length of the partially split joints, joint the edges and glue again. I understand this might require adjusting the perimeter shape.

Re: Spilt glue line reapir

#4

Re: Spilt glue line reapir

Jesse Cloud

I know this doesn't answer your question, but I would make "Pooh Tooh".

Use the original as a template for routing Tooh.

Tell the grandkid that Pooh had a nice spa weekend with lots of honey and feels like a brand new Pooh.

Re: Spilt glue line reapir

#5

That's what I was thinking too...

John in NM

Trying to continue the split may deviate from the glue line. I'd probably saw down the line and plane the edge to reglue, then just work the curved outline down so it looks ok.

Then I'd probably send it off to the stabilizer so it wouldn't split next time the kid put it in the dishwasher. The culinary elite shudders at the mere thought of getting a $400 knife near stabilized wood, but it's actually quite practical for the rest of us. Got to use epoxy for the joints though, the resin cure involves heat.

Re: Spilt glue line reapir

#6

Re: Spilt glue line reapir

AZ in Colorado Springs

I'd think you can split it as you suggested. Doesn't need to follow the glue line. As long as neither part splinters, you'll have two complementary parts. Don't clean the old glue too much or you'll create a gap. Glue it back together using epoxy. You may have to make some clamping cauls to fit the two sides of Winnie.

Re: Spilt glue line reapir

#7

Re: Spilt glue line reapir

Bill Tindall, E.Tn.

Steam it and the glue will let go if it is Titeboned or hide. I am imagining something like suspending it over boiling water with a cover on the pot, or some such.

Re: Spilt glue line reapir

#8

Re: Spilt glue line reapir

Dustmaker Mike

Hum steam. It was just plain Elmer's wood glue.

Re: Spilt glue line reapir

#9

Re: That's what I was thinking too...

Dustmaker Mike

I had repaired a Pig cutting board I made in middle school a bunch of years ago by cutting it along the split jointing the edge and re-gluing. Lets just say the pig was really deformed. That is why I was thinking of using a sharp knife and trying to follow the glue line. I also thought of using a piece of contrasting wood at the split to fill the gap caused by the blade, but that would add another glue line. I am thinking the steam method might work along with a knife.

Whats the worse thing that could happen?

Re: Spilt glue line reapir

#10

Re: Spilt glue line reapir

Dustmaker Mike

I looked at doing that and my daughter and wife said Nope. I said I could clean it up leave the splits drill a hole in it and she can use it as art. She is undecided on that right now.

Re: Spilt glue line reapir

#11

Re: Spilt glue line reapir

Dustmaker Mike

Thanks I might try steam to get moisture back in the wood. Then use the knife to split it.

Stay tuned

Re: Spilt glue line reapir

#12

Re: Spilt glue line reapir

Barry Irby

I was elected to repair my Grandmother's table she had built many years ago. It is a drop leaf walnut dining table. One of the wings had a split starting on the glue line. I used a knife to finish the split. A really cheep hollow ground butchers knife. (not $400, probably $5 new, that I found) It worked perfectly and much easier than I expected. No heat, no steam, just popped the joint. I was sort of shocked at the ease.

Took the table to a friend to apply the finish. He found two more failing joints and fixed them.

The steam may cause all the joints to fail. Might be a good thing. Then you can clean them all and Use Titebond ll or lll or epoxy.

Re: Spilt glue line reapir

#13

Steam will work

Bill Tindall, E.Tn.

Actually just heat will work but there is a great risk with just heat. The wood may dry too quickly and split somewhere else.

Here is something to try. Maybe the dishwasher can be rigged to make a hot steamy environment drying its drying cycle, by adding excess water during this cycle Once the wood gets near the boiling point of water in a damp environment the glue will loose nearly all its strength and modest force will pop it apart. It takes about 10 min of steamy environment to loosen a mortise and tenon done with white or yellow glue.

Re: Spilt glue line reapir

#14

Re: Spilt glue line reapir

John K Jordan

> use it as art. She is undecided on that right now.

Perhaps offer to make a new Pooh (hmm, that doesn't sound quite right) for function while retiring the one with sentimental value to art?

JKJ

Re: Spilt glue line reapir

#15

Worth a try then...

John in NM

The steam idea is a good one, provided there is just the one joint you want to pop. Steam would be handy for scraping the joint clean too.