Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Drill bit lube for Oak?

Posts

Drill bit lube for Oak?

#1

Drill bit lube for Oak?

Kevin French

So after 2 1/2 years into retirement I screwed up and took a job. I'm working with a guy who is building Adirondack style stair made out of used Wine and Whiskey barrels.

One of the additional things he make is candle holders. These have 5, 2 1/4" holes in a oak barrel stay. The problem is he's not getting enough holes drilled before the bit dulls. The Drill Press is on the slowest speed and I'm using as light a touch as I can but we're still getting powder after about 8 stays (40 holes). He's worked with Old Milwaukee and Irwin bits and likes the Irwin's better. I'm looking for a local sharpening service. Is that the life of one of these bits before resharpening?

Someone told him there was a lube that would lengthen the life of the bits. I've never heard of such a thing other then using something like bees wax. I told him I'd bounce it of you guys and see what's out there.

Any help would be greatly appreciated I have to go in tomorrow and try to knock out 30 sets for an on going show this weekend because he blew thorough his supply today, the first day of the show.

Re: Drill bit lube for Oak?

#2

Re: Drill bit lube for Oak?

Kevin French

We're using a Forstner Bit and the holes are only a 1/2 to 1/4" deep on the curve of the stay.

Re: Drill bit lube for Oak?

#3

Re: Drill bit lube for Oak?

TomD

I would try some bits sold by lee valley. There a lot of bad bits out there, some look great and won't eve cut a hole. You could try wax for a lube, there is a special wax for saw blades, but overall it is most likely to be your bit quality. There are carbide bits, but I would have to be sure, because geometry is all important.

http://www.leevalley.com/en/wood/page.aspx?p=63566&cat=1,180,42240,

http://www.leevalley.com/en/wood/page.aspx?p=62137&cat=1,180,

If you can stand working with them. pattern routing is another option, and router bits will last. You can get very high quality ones and they are relatively easy to sharpen.

Re: Drill bit lube for Oak?

#4

Re: Drill bit lube for Oak?

Kevin French

I thought about a Bee wax/mineral spirits solution that I could just paint the bit between holes.

Those Maxi-cut bit look like another option

Re: Drill bit lube for Oak?

#5

Re: Drill bit lube for Oak?

Kevin French

Doing a bit of research, I found this vid that should take care of most of my problem. I think I'll still try to get him to buy a better brand of bit, but now I know I can sharpen them.

Re: Drill bit lube for Oak?

#6

Re: Drill bit lube for Oak?

John K Jordan

I don't know if it will help in your case, but when using a forstner bit I always direct a continuous stream of compressed air into the back of the bit (or into the hole on a deep bore). This keeps the bit a lot cooler and the chips clear. I think it keeps the bits sharper longer but can't say for sure since I've gone to carbide bits.

I think it is important to keep the bit cool, at minimum to keep from burning the wood. The drilling guides I use say make several shallow cuts with larger forstner bits and allow the bit to cool between cuts.

Also, I've always wondered if lowering the drillpress quill too slowly is harder on the bit. For example, bandsaw blades cut better if the wood is advanced at the right speed. Too slow and the teeth are rubbing and making fine dust. I read somewhere that this can heat up the blade faster and wear the teeth quicker. (I have no hard data on that but a machining book I have says that is true when machining/drilling metals.) If true, spinning the forstner bit on the wood by advancing too slowly (during each incremental cut) might contribute to overheating and wear the bit. Perhaps someone else has experience with this and will comment.

(PS, the next time you retire try to stick with it!)

Re: Drill bit lube for Oak?

#7

Re: Drill bit lube for Oak? *LINK*

John McGaw

I'm not sure what sort of Forstner bits you are trying but there are carbide-tipped bits which do the same job. Not cheap but probably a lot less hassle than what you are going through now. I've given one example below but they are certainly available from more high-end makers.


Carbide Bit

Re: Drill bit lube for Oak?

#8

Re: Drill bit lube for Oak? *LINK*

Jim Dillon

Kevin,

I second the Lee Valley forstner bits. I've had luck with Dri-Cote lube for my forstners.

Jim


Bostik Dri-Coat Lube

Re: Drill bit lube for Oak?

#9

Re: Drill bit lube for Oak?

John in NM

Yeah, learn to sharpen them, the rim in particular. Sharpening services often skip that in my experience.

I'm still pretty surprised that they dull so fast. I think I would try carbide, all that other stuff with a Forstner style bit is just gimmick.

Re: Drill bit lube for Oak?

#10

Re: Drill bit lube for Oak?

Dick Coers

I'm very pleased with the carbide tipped bits I bought at Woodcraft. You could also make a fixture with an oversized hole, and use a router with a guide bushing. If you do a lot, the fixture could have all the holes in it, or for just a few just have one hole and move it.

Re: Drill bit lube for Oak?

#11

Re: Drill bit lube for Oak?

Ralph Lipeles

How about roughing out the hole first with a spade bit then doing only the final cleanup with the Forstner bit.

Re: Drill bit lube for Oak?

#12

Re: Drill bit lube for Oak?

Kevin French

Thanks for all the help. I bought a small DMT bar that worked well with a diamond plate I had.

Thanks Jim for the lube link, we'll give that a try

Routing the holes won't work. There are no straight lines to a stave and a lot of differences between staves. Will look into spades, the owner and I talked about them.

We spent 5 hours today working on them, mostly trying to get an old Darra James ToolKarft Drill Press to work after have to change the belt. I ended up bring 10 home and drilling them out on my press

 photo P1220661.jpg

 photo P1220663.jpg

This is one of the unfinished chairs and tables we will be working on next week after the show.

 photo P1220659.jpg

Re: Drill bit lube for Oak?

#13

Re: Drill bit lube for Oak?

William Duffield

Beeswax or PAM for a lubricant.

BorMax Forstners by Famag.

Drilling technique: The chips carry the heat away from the cutting teeth. Plunge quickly. As soon as shavings stop rapidly being expelled from the top of the bit, quickly retract the bit from the wood. Leave it turning, to help cool it. After the chips have been slung out of the bit, replunge, again quickly, and just as quickly retract it.