Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

OT - Rust Prevention

Posts

OT - Rust Prevention

#1

OT - Rust Prevention

Terry Alexander

I just got possession of a pretty old drill press. Big drill press. It had been left in a shop that had a leak. Lots of rust. I took the base off (very heavy) and the top part and the drilling table. Had the base sandblasted and the 5' long pipe sandblasted also. Am paying a machine shop to put a new surface on the drilling table. Top part (motor, light, mechanics) are all ok. I am going to paint the base.

Here's the question: I'm not real sure what kind of metal the pipe is that hold all the 3 major parts. I "think" it is some kind of galvanized steel or maybe coated cast iron. Now that it is rust free, what should I put on it to keep it that way. Can't paint it because you move the drilling table up and down and you can even move the top part (not sure why you'd need to). Guy at the machine shop said to just put grease on it. I'm not sure that is the solution. But if y'all say he is correct, then grease it is. I am thinking about past wax, like my tablesaw top.

Appreciate your expert advice!

Terry Alexander in West Texas

Re: OT - Rust Prevention

#2

Re: OT - Rust Prevention

John in NM

Mast is most likely steel. There is no magic solution that I'm aware of to prevent rust on a working tool, any kind of plating will scratch as well as add a few thousands thickness to the part. Any coating will wear off quickly where any moving parts rub.

I've been messing around with some Evapo-Rust at work. We bought a jug to see if it was less time or effort than grinding rust off steel stock before painting. It is purported to be a rust preventative as well, so you might look into that - stuff would still come off where the table moves, but it's also fairly cheap, benign, and easily applied with a spray bottle.

If money is no object, you could have the thing nitrided. It gives you a hard and slippery surface that is about as wear resistant as it gets, and doesn't add thickness like plating does. Hard to find vendors who do it though, as the chemicals and process tend to be a bit nasty as I understand it. Finish is dark grey to almost black and tends to come out dull if not polished as part of the process.

Re: OT - Rust Prevention

#3

Re: OT - Rust Prevention

Ralph Lipeles

I use paste wax. Over time some rust appears. I rub the spots with steel wool and paste wax. It does a good job.

Re: OT - Rust Prevention

#4

Re: OT - Rust Prevention

Ray - Middletown, IN

Had a small shop fire a couple of years ago with water damage. Lots of rusty tools that I used Evap-O-Rust on. Worked well for the most part but two things emerged that I didn't like. One was it did a poor job of prevented more rust from forming. The other was on all of my calipers the springs broke while in the solution, all at the same location. It also left a coating but that was fairly easy to remove.

Ray

Re: OT - Rust Prevention

#5

Re: OT - Rust Prevention *LINK*

Jim Dillon

Hi Terry,

I've had good luck with Boeshield T-9. Read some of the reviews to see if it might fit your needs. I don't think the lubrication properties of T-9 would be a problem in your application.

Jim


Boeshield T-9

Re: OT - Rust Prevention

#6

Re: OT - Rust Prevention

John K Jordan

Not for the post but perhaps the cast iron table surface: I have a sliding tablesaw attachment made by Robland, the European tool company. They recommend something I never heard of for cast iron surfaces.

They say to rub talc powder on the surface with a chalkboard eraser every few weeks. They say this will fill in pores in cast iron and keep out moisture and prevent rust. I have been doing this instead of my usual wax on other surfaces and have seen no rust.

I found pure talc that doesn't smell like a the baby's room on Amazon, marketed to billiards players.

JKJ

Re: OT - Rust Prevention

#7

Re: OT - Rust Prevention

Terry Alexander

Wow...that is unusual. I happen to have an Oldhausen professional pool table and I do have some talc (I shoot a pretty good stick....nothing professional).

Q: Do you use the talc on your table saw top?

If so, does the wood slide as easily as when waxed?

Thanks for the response.

Terry Alexander in West Texas

Re: OT - Rust Prevention

#8

Re: OT - Rust Prevention

John K Jordan

Unlike the add-on sliding table, the cast iron table on my saw (PM66) is polished and does not appear porous. I know very little about cast iron but I read some types are more porous than others and would presumably benefit more by the talc.

I usually use Renaissance Wax ("microcrystline" wax, whatever that means) on my lathe bed and tool rest, bandsaw table and table saw. It does make things slide better and seems to protect the surface.

JKJ