Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Glue for Steam Box

Posts

Re: Glue for Steam Box

#26

Re: I can't see the pics,

William Duffield

I have no clue what happened. They were there when I posted the message. I'll try again.



Re: Glue for Steam Box

#27

Re: I can't see the pics,

Keith Newton

Ah, Those mostly look like glass boats, except maybe the far left in the top image. Do the wooden ones have bows and turn of the bilge that rounded, or is there a chine?

I wouldn't think for a thin soft wood, that most of the length would need steaming.

Are you into sailboat racing now?

Re: Glue for Steam Box

#28

Re: I can't see the pics,

William Duffield

The white one in the first picture and the red and white one in the second are the same boat. First pic was immediately after it was restored in the early '90s; second was a bit later during a race. It was built in '33 and was National Champion in '34. All the Moths of that vintage were wooden, and almost all were hard chined. Later Classic Moths were fiberglas, or glass hull and plywood deck.IMP TOO was a unique design, the hull and deck being a totally monolithic, aerodynamic, smooth shape. The only flat surface was the transom and foils.

Many of even the oldest ones had a round nose. Typically, they were bricked up and carved, like this one, made of mahogany. The deck and hull, like IMP TOO, are Atlantic White Cedar.


IMP TOO's nose was carved from a single white cedar knee.


Some of her planks, for example the garboard and the plank next to it and the central deck planks, don't need to be steam bent.


The chine planks are more strongly curved, and either need to be made from much thicker (more expensive and much more difficult to find) board, backed out and a lot of wood removed to fair them, or need to be steamed or need to be stripped.

I've been into fixing up old pboats. I thought I might race them, but my knees just won't work in boats this small.

Re: Glue for Steam Box

#29

Re: gorilla

William Duffield

I've seen the Rodrigues video, and although the method is ingenious, neither the process nor the results are to my taste. The hollow of the seat looks like it was cut by a machine, and is incompatible with the hand shaped surfaces of the rest of the chair. A lot of people wouldn't notice, but some would realize there was something "a little off" even if they couldn't put their finger on it, and we would know what had been done. Of course, with some hand work with a shave, the shape could easily be refined to a contour that would have been made completely by hand.

I've seen another ingenious machine that was designed to reproduce the shape of an existing chair seat, using a router and a pantograph setup. It would need a lot of cleanup, but would get you a set of seats that all looked hand carved, but were close enough that no one would think they were not members of the same set.

Re: Glue for Steam Box

#30

Re: Mike Dunbar

William Duffield

The Moth has had a complicated history. Basically, however, the class rules for classic moths are a lot more restrictive than the International Moth, which split off in the 1969.

The Classic Moth is explained on the Classic Moth Boat Association website, mothboat.com

If you want to see what the modern concept of a development class looks like, do a Google Image search on "international moth" These are just too radical for us old geezers to sail, and I don't think they are appropriate for most young'uns who want to move up to something beyond an Opti. Of course, they could easily step up to a Laser, but as with other one design classes, they don't get building experience along with the sailing experience. Instead, their parents just throw money at it.

Re: Glue for Steam Box

#31

Re: gorilla

TomD

"I've seen the Rodrigues video, and although the method is ingenious, neither the process nor the results are to my taste."

Plus I am actually looking for situations where I can use everything from my guttering adze to my lancelot. If one is selling chairs, the main deal is to make them so every reasonable seat fits them. Custom, I want them to fit me (which pretty much means the above criteria are met for all the ladies in the in the house).

Re: Glue for Steam Box

#32

Ellis Walentine

Tight fitting plywood joints

Ellis Walentine

Hi William,

I might suggest gluing in fillets in all the corners to quadruple (or more) your available gluing surfaces.

Ellis

Re: Glue for Steam Box

#33

Re: Fillets-R-Us

William Duffield

Fillets have been there from Day 1. They're an essential part of the structure. The first photo shows the steam outflow end of the box, opened.


It is designed to accept either this terminator, with adjustable steam outflow holes, or a collar to join it to another six foot box extension.


Since these parts slide over the box sections, their reinforcing strips have to be on the outside.

I still need to install dowel rods to keep the wood being steamed up off the bottom of the box. The box is on its side, with two handles (one visible in the pic) on the top.

Here is a view of the end closure with a better view of the steam regulator. It is stacked on top of the collar that would replace it to join two lengths of steam box together.