Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

An Actual woodworking question......

Posts

An Actual woodworking question......

#1

An Actual woodworking question......

Barry Irby

Do we have a mathematician? Anybody know trigonometry? About fifty years ago I taught myself trig to get by on the college prep tests. Now all I remember is that trig EXISTS.

There must be an on line program for this. Somebody clue me in.

I am repairing a door that has glass in the top half. The panes are a series of trapezoids and triangles. I need to replace some of the sticking or molding that holds the glass in place. So, if I have and equilateral triangle that is 13 1/2" on the base and the other two sides are 11", what are the angles. I know they total 180 degrees and I know I must bisect them to get the cuts on the sticking. I also know the height of the triangle is 8 1/2" measured for the center of the long side.

I was going to fudge them into submission, but it woudl be easier if I had a good starting point.

What are the angles in the triangle?

Re: An Actual woodworking question......

#3

Re: An Actual woodworking question......

John K Jordan

52.147, 52.147, and 75.706

The math is not hard but the little triangle solver app I keep on my phone requires no pencil and paper! And it's a lot faster. I use it a lot, especially when planning and laying out farm buildings, rafters, etc.

JKJ

Re: An Actual woodworking question......

#4

Re: An Actual woodworking question......

As I recall the 1"/year is for hardwoods

In a pinch you can lay out the dimensions you have a on a piece of paper, or the actual work piece, and measure the angles with a protractor or table saw miter gauge.

Re: An Actual woodworking question......

#5

Do you want to know how to do it?

John in NM

Or just answers? John K already gave you the answer, so I'll give you the trig.

Split your isosceles into two right triangles.

So the short leg of one of the right triangles is 6.75 and the hypotenuse is 11. The inverse sine of that ratio gives you the smaller angle (multiply it by two to get the angle of the isosceles). The inverse cosine of the same ratio gives you the paired angle of the isosceles.

You can find any length or angle of a right triangle with any two measurements, either one length and one angle or the two non-90 angles.

Sine (angle) = opposite length/hypotenuse

Cosine (angle) = adjacent length/hypotenuse

Tangent (angle) = opposite length/adjacent length

Re: An Actual woodworking question......

#6

Re: Do you want to know how to do it?

Barry Irby

Thanks, I poked around on the inter web and found a bunch of info.

Worked out the angles. JKJ nailed it.

It was an interesting little project. Made the sticking to match the existing stuff. I like the fact that I used a pine shelf I found in the house as stock. The muntins had been chewed by a dog. I pried out all the sticking the dog had gotten to. Use a router to trim away the ribs of the muntins that were damaged. Glued on replacement stock I had made for the purpose. Cut a piece or Lexan to replace the pane someone broke out to get into the house. Cut the sticking with my miter saw. Used a block of wood to hold some of them at right angles to the fence. Worked out the angles of some of the trapezoids on site.

Thanks for the help...the door that looked like it had been thoroughly chewed by a large dog looks like new.

Re: An Actual woodworking question......

#7

how did a dog  ...

AZ in Colorado Springs

... chew on the top part of the door?

Re: An Actual woodworking question......

#8

Re: An Actual woodworking question......

Derek Cohen (in Perth, Australia)

Hi Barry

You assume that the original maker used exact calculations and that, therefore, replicating this is helpful. But what if they laid it out by eye and "fudged" (i.e. fitted) the pieces by hand and eye?

It's similar to fitting moulding around a carcase - square corners are expected, and mitres should be 45 degrees, but often they are not that exact.

I would trace the existing parts on paper, and work with that.

Regards from Perth

Derek

Re: An Actual woodworking question......

#9

Re: how did a dog  ...

Barry Irby

The dog got the bottom row of lites and a few on the second row. Some of the tooth holes looked like they were 1/8" in diameter or slightly larger. Some of it was torn completely off, shredded.

The sticking was stapled in and did not come out as easily as I thought it might. To get it out you need to pull the staples and slide it straight out the front, but getting the staples out was not that easy and I didn't really care because I was replacing the sticking anyway. I broke most of it. One piece that had only a few holes in it, I left and puttied the holes. I replaced about ten pieces. Fairly easy after working out the angles and how to cut them.

Re: An Actual woodworking question......

#10

Re: An Actual woodworking question......

Barry Irby

Derek, this is a manufactured door. I assume they pre-cut the sticking and glass. The bottom row of glass was tempered so would have had to have been purpose made. I am betting they laid the door out on a big work bench, caulked the openings, and installed the glass and sticking.

Re: An Actual woodworking question......

#11

Re: An Actual woodworking question......

Barry Irby

Derek, this is a manufactured door. I assume they pre-cut the sticking and glass. The bottom row of glass was tempered so would have had to have been purpose made. I am betting they laid the door out on a big work bench, caulked the openings, and installed the glass and sticking.

In the end it wasn't as hard as I thought