Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

coping saw blades for wooden rings

Posts

coping saw blades for wooden rings

#1

coping saw blades for wooden rings

Brad Bransky

I want to make hardwood finger rings for holiday gifts.

Forstner bits and hole saws burn the inside and outside.

What coping saw blade would you recommend for such as Copobolo, Ebony, etc.?

Thanks, Brad

Re: coping saw blades for wooden rings

#2

Re: coping saw blades for wooden rings

Ralph Lipeles

Brad,

You might try significantly reducing the drilling speed to eliminate the burning. Those bits create a lot of friction and slowing the speed will reduce the rate of friction heat buildup.

Ralph Lipeles

Re: coping saw blades for wooden rings

#3

Re: coping saw blades for wooden rings

Dick Coers

There is going to be a lot of cleanup with coping saw cuts as well. A high quality forstner bit will still work better. Please keep in mind that a lot of people are allergic to cocobollo. Wearing a ring of that will result in a nasty event, possibly cutting off the ring from swelling.

Re: coping saw blades for wooden rings

#4

allergic reaction to wood

John K Jordan

Note that the primary hazard for most people is the DUST from working cocobolo and other woods, mostly from breathing but also from skin contact. (Even eastern red cedar will give me a mild rash if dust is trapped under my watch band for some hours.) The literature indicates very few have an allergic reaction to various species of the solid wood on things like knife blades, guitars, bowls, etc., where skin contact is minimized.

But I've read medical reports of horrible reactions when cocobolo (and other species) are kept in contact with the skin of who are very sensitive. Just google "cocobolo wood allergy" and see photos of inflamed wrists, earlobes, etc. Ack!

I like the chart on this page:

http://www.wood-database.com/wood-articles/wood-allergies-and-toxicity/

JKJ

Re: coping saw blades for wooden rings

#5

Cocobolo

Mark Mandell - Gone Round In New Jersey

There are two classes of people:

1. Those who are allergic to it.

2. Those who will be allergic to it.

[ergo - find a different wood for the rings]

Re: coping saw blades for wooden rings

#6

Re: coping saw blades for wooden rings

Barry Irby

I have made dozens of wooden rings. Never occurred to me to use a coping saw. I turned them on a lathe. Easy and quick once you get into it. (If you are not a turner, this could be your welcome to the vortex.)

Re: coping saw blades for wooden rings

#7

Sounds Like

Mark Mandell - Gone Round In New Jersey

he's trying to "punch" them out of 1/2" mol board stocks: Drill a hole for the finger size then cut the outside diameter with a holesaw or cope it.

Re: coping saw blades for wooden rings

#8

JL

Re: coping saw blades for wooden rings

JL

I drill a number of holes in hardwood (seat blanks, legs, stretchers, etc.).

I use Forstner bits or brad point bits.

I drill slowly and I have a vacuum hose near the drilling point. If you have a vacuum (or an air stream from a air compressor) on the bit, it will sometimes cool it enough. I also drill at a slow rate.

Re: coping saw blades for wooden rings

#9

Re: Sounds Like

Barry Irby

Occurred to me after I wrote that he might be making them asymmetrical.

Re: coping saw blades for wooden rings

#10

Re: coping saw blades for wooden rings

John in NM

My first take is a lathe, as Barry suggested.

But you can also make very quick rings using nested hole saws if you solve the burning problem. You drill the smaller size and then use it as the pilot for the larger. McFeely's used to sell the arbors to do that, they called them "oops arbors" if I remember correctly.

I've not had hole saws burn significantly, but then I'm not running them through Cocobolo. Maple or oak yes. Low speed, compressed air to clear the gullets and cut.

Re: coping saw blades for wooden rings

#11

Oh yeah...

John in NM

And post some pics! Sounds like a neat project.

Re: coping saw blades for wooden rings

#12

Re: coping saw blades for wooden rings *LINK*

Bruce, a MN Galoot

He uses different tools, but look at Mattheis Wandel's site.


Wooden rings

Re: coping saw blades for wooden rings

#13

Re: Sounds Like

Brad

Unfortunately, using a Forstner bit and hole saw, they are coming out asymmetrically which is why I want to try this.

http://www.youtube.com/watch?v=v8ccr8sPQ_w

Re: coping saw blades for wooden rings

#14

Re: Sounds Like

Barry Irby

I had forgotten how "sooty" ebony can be.

If you wanted to make one or two I suppose that woudl be a good way to do it. I COULD do it that way. If I were making more than one, it would drive me nuts. The second major tool I bought was a lathe.

Did you watch the guy making them on the drill press? I did not, but I can visualize doing it that way. Or you could just clamp a hand held drill to a top and make a little lathe.

By asymmetrical I meant seriously asymmetrical. Perhaps with a setting or stone on one side.