Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Plywood continuing to shrink......Gripe

Posts

Plywood continuing to shrink......Gripe

#1

Plywood continuing to shrink......Gripe

Barry Irby

Went to Home Depot and Lowe's for a sheet of 5/8 plywood. I could have sworn that I found a sheet a year or two ago that was actually 5/8" No luck.

I am working on a house about forty years old and had to pull out some rotten floor. 1/2" subfloor with 5/8" underlayment. The only 1/2" they had was a being sold as 7/16. Then I notice the tag had the actual thickness stated as a decimal fraction. Its actually 13/32". What was being sold as 9/16 was actually 17/32".

This disappearing thickness sure makes it difficult to patch a floor and keep it flush.

Re: Plywood continuing to shrink......Gripe

#2

Barry Barry Barry

Mark Mandell - Gone Round In New Jersey

Git with the program, dude. No patches allowed. You rip it out to the studs/joists and put it ALL IN NEW.

Didn't you get the memo?

;)

Re: Plywood continuing to shrink......Gripe

#3

Re: Plywood continuing to shrink......Gripe

Larry

Boy, where have you been? Plywood has been under size for at lest 10 years.

Re: Plywood continuing to shrink......Gripe

#4

How low can we go?

Barry Irby

You are right. It has been undersized for probably more than ten years, but this is the first time I have noticed they have taken another 1/32 off it. Pretty soon 1/2" will be the new 5/8".

At some point it seems it woudl be more honest to just sell it labeled correctly and priced accordingly and let us choose to use the new thinner stuff.

Re: Plywood continuing to shrink......Gripe

#5

Re: How low can we go?

Basil

A 1/32" here, another 1/32" there and pretty soon you have another sheet of plywood to sale.

Re: Plywood continuing to shrink......Gripe

#6

Re: How low can we go?

George Koch

The same thing happened 50+ years ago with dimension lumber

Re: Plywood continuing to shrink......Gripe

#7

Re: How low can we go?

AZ in Colorado Springs

I'm not disagreeing with the gripe, but the fractions lie on a continuum (or number line). As 1/2 gets thinner, so does 5/8 and the rest. So, go for a fat 1/2 by getting the mislabeled 5/8. It's inflationary, but you can't escape that. It also doesn't completely solve patching the floor smoothly, but it might reduce the mismatch?

Good luck

Re: Plywood continuing to shrink......Gripe

#8

Re: Barry Barry Barry

Barry Irby

Good Idea. A thinner floor would preserve the ceiling height for when I install the laminate floor.

Re: Plywood continuing to shrink......Gripe

#9

Re: Plywood continuing to shrink......Gripe

Jerry Nicholson

Buy some 3/4. It will probably be just a little over 5/8 and will have already started to delaminate. Just peal off the bottom lamination and VIOLA - 5/8 Plywood! The last time I wanted some plywood I gave up because it was all warped and delaminated garbage.

Jerry

Re: Plywood continuing to shrink......Gripe

#10

Metric's no better

Jesse Cloud

Not too long ago, the Baltic Birch I would buy at the local lumber yard was 19mm.

The stuff I bought yesterday was 17.5 mm. At least it had a "17,5" stamp on it, so it wasn't pretending to be something it wasn't.

Re: Plywood continuing to shrink......Gripe

#11

At least with dimensioned lumber.....

Barry Irby

They picked some new numbers and have stuck with them since.

Plywood, not so much. Not only do they keep slimming it down, they switch back and forth to metric. Sometimes underlayment is 1/4", actual and sometimes its scant and sometimes its 5mm.

I was at one of the big boxes (first mistake) looking for 1/4" oak plywood, which they used to carry. Not any more. Now they have "Whitewood" primed on the back. Whatever that is. Got to go back and cipher on that some more.

Re: Plywood continuing to shrink......Gripe

#12

Just looked at Lowe's site....

Barry Irby

They have plywood listed as being 22/47.....Took me a minute to realize that was 22/47". Sheesh. I can't think in 47ths.

Re: Plywood continuing to shrink......Gripe

#13

Kneale Brownson

Good Reasons For Owning A Planer


Re: Plywood continuing to shrink......Gripe

#14

Whitewood

John K Jordan

>Now they have "Whitewood" primed on the back. Whatever that is.

I asked a manager once about "whitewood." He said it was poplar (or pine or linden or spuce or hemlock or aspen) or whatever mystery wood was cheapest at the mill. I get all my wood facts from Home Depot managers and "associates."

JKJ

Re: Plywood continuing to shrink......Gripe

#15

I haven't found that they stuck with the numbers..

John in NM

I have recently bought 2x4's and received 1 3/8 thick lumber instead of the hair under 1 1/2 to which I am accustomed. When I was a kid my dad explained why the 2x4 was 1 5/8 thick...

In an industry that thrives on writing, applying, and checking codes, I marvel that this sort of thing is tolerated.

Re: Plywood continuing to shrink......Gripe

#16

Re: How low can we go? - the numbers

TomD

Russ

"At some point it seems it woudl be more honest to just sell it labeled correctly and priced accordingly and let us choose to use the new thinner stuff."

John

"In an industry that thrives on writing, applying, and checking codes, I marvel that this sort of thing is tolerated."

I think these ideas may be connected. When they sell a stamped and rated panel as 5/8, they are saying you can install that where your plans call for 5/8. Reducing a panel all the way from 5/8 to 1/2 reduces the strength about 40% and it almost halves the stiffness. So how can they do that (or nearly that)? Presumably because they have new testing methods/data and all importantly new standards of construction to deal with.

When I look at older houses, and newer houses, the spans between joist/studs and rafters are tighter on the newer houses, pretty much everything is 16" while 24 was relatively common at one time. These days people want more house and amenities, not a single squeak, and all that jazz. So even though there are wood efficient methods of building that are promoted, when it comes to actually building decent houses, people want the backing for all the crap they hang on the walls, the certified quiet floors, the stick trusses not piece framing, and so on. The end result is that houses are enormously overbuilt so it actually makes sense to reduce the panel thickness. Or that might be part of it. The profit motive is only going to be good so far, this stuff is rated. Does HD want to have to pay off every home lost in a hurricane?

So for instance assume your rafters are set at 16 not 24 to maintain the same strength in the panel you could probably drop the thicknes to 1/2 (root of 1.5). To do the same on stiffness which is probably the main point, would be maybe 9/16

Re: Plywood continuing to shrink......Gripe

#17

Re: Another issue is variable thickness

Larry Clinton At Frankfort, (Central) Indiana

When my son and I built his kitchen cabinets I set up my saw to cut dado's in the 3/4" side, top and bottom panels to fit the back panel. I set it up, cut a dado in a scrap piece and tried the fit on a sheet of Birch plywood (supposedly 3/4" or .750"). I found I went from quite tight to way loose when trying the test piece on the new sheet. So I tried several sheets and then measured the thickness with precision Digital Calipers (or micrometers ~ can't remember). As I remember there was .010 to .016" difference in thickness in a couple foot of the new sheets. I knew the panels would not be full thickness, but sure didn't think they would vary in thickness by a 1/64".

Re: Plywood continuing to shrink......Gripe

#18

Re: Good Reasons For Owning A Planer

AZ in Colorado Springs

OK, I'll bite on this one. Do you put plywood through your planer?

Re: Plywood continuing to shrink......Gripe

#19

I'll admit to it

John in NM

Rarely, but now and then I need some ply to be just a bit thinner.

Re: Plywood continuing to shrink......Gripe

#20

Kneale Brownson

Re: Good Reasons For Owning A Planer

Kneale Brownson

I've never put plywood through a planer. I HAVE matched the thickness of floor boards in an old building using a planer, and I've substituted solid wood for rotted subfloor material, again using the planer to match thickness of unaffected subflooring.