Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Dust vs Workshop Stereo Components

Posts

Dust vs Workshop Stereo Components

#1

Dust vs Workshop Stereo Components

don stephan

My Sony amplifier finally died, so will be getting a replacement. The amp and CD changer are in cabinet in furnace room, but I've always left the cabinet doors open to minimize heat buildup. The insides of the amp are covered with layer of very fine white dust, and I'm wondering if it is possible to protect against the dust in the future. I drilled a number of 1/2" diameter holes in the top and bottom of the cabinet, so in theory I could add a small fan and perhaps some sort of filter material on the outside of the cabinet. But the dust looks so fine . . .

Wondering what others have done. Thanks.

Re: Dust vs Workshop Stereo Components

#2

Re: Dust vs Workshop Stereo Components

Tom Dunlap

My shop music systems have either been downgrades from in the house or cast-offs scavenged from the curb or trash bin. When one dies there is always another so I never worry. My ears aren't that good at the best of time.

I've been using my phone to stream web radio through some computer speakers. Compact and cheap. Works good enough for my shop ears. No worries about dust getting to the innards.

Tom

Re: Dust vs Workshop Stereo Components

#3

Re: Dust vs Workshop Stereo Components

David Yoho

I have an old "boom box" in my shop that I used to have a portable CD player, much like an old Walkman, plugged into. The downside to that arrangement was it only played the single CD and then either had to be switched out or played again. When I got my smart phone I soon realized the same cable I used to connect the CD player would also plug into the earphone jack of my phone. I just had to flip the switch on the boom box to the AUG setting. Now whenever I go to the shop I take my phone with me and plug it in. I put on a playlist I made for longer play or an album for shorter. The nice thing is if I get a call or text on my cell phone it mutes the music so I can respond if needed.

If the boom box ever dies from old age or dust, I'll simply replace it with a Bluetooth speaker and keep getting up! An MP3 player would work just as well as a phone.

Re: Dust vs Workshop Stereo Components

#4

Re: Dust vs Workshop Stereo Components

Jim Matthews

I find most dust settles after I've been in the shop.

It makes sense to ventilate audio gear, if it's overheating.

However, if this is done in a dusty environment - you're

pulling more dust (along with the air) over the various parts.

Unless the gear is also getting filter in line with the fan,

I would suggest that you're likely to create more trouble.

Instead, place a pillowcase over the equipment when not in use.

Take a vacuum to the case when you can, and open the case

once a year for a more thorough cleaning.

Alternately, put the audio gear in another space and string longer cables.

Re: Dust vs Workshop Stereo Components

#5

Re: Dust vs Workshop Stereo Components

paul woolson

I did just what you are suggesting. I made a raised panel box but instead of putting panels on the sides, I put furnace filters. On the front I replaced the panel with plexi so that the remote would still work.

It started getting warm so I put in a couple of computer fans. Works like a charm.

Incidentally, if you are looking for a receiver, I was just getting ready to list on on ebay. Onkyo. Drop me an email if you have any interest. paul at woolsonsoundcraft.com

Re: Dust vs Workshop Stereo Components

#6

Re: Dust vs Workshop Stereo Components

William Duffield

I do the same with my iPad. The speakers were originally for an iPod, which plugs into the top of the unit, but I don't have the iPod anymore. If this one dies, I'll get another one with Bluetooth, so I won't need to plug an audio cable into the iPad every time I take it out to the shop and unplug it when I leave the shop. If the shop weren't so far from the house, Bluetooth would allow me to put the iPad on "shuffle" and "repeat" and I could leave it in the house, if music were all I used it for in the shop. Of course, I use the iPad for much more than just music in the shop. With the iPad, I can store many hours of music, program as many custom play lists as I want, listen to podcasts, or even a vast selection of radio stations with Apple Music Radio.

Re: Dust vs Workshop Stereo Components

#7

Re: Dust vs Workshop Stereo Components

Yonak

The dust on electronic equipment issue has been addressed before and I believe the consensus at that time was the dust really doesn't hurt anything unless the box is just clogged with dust. At least, that's the impression the conversation left with me.

Re: Dust vs Workshop Stereo Components

#8

Re: Dust vs Workshop Stereo Components

John McGaw

Dust damage will be far more likely if the amplifier in question is designed with poor heatsinks and air circulation and is run at high power levels. While the first two conditions seem likely for a cheap component one would put in the shop the third one isn't; not unless one is trying to run it loud enough full time to overcome the whine of a tablesaw with massive speakers.

I have been getting along for a long time using the Nutone intercom/radio I installed soon after moving into the house and putting up the wall to divide the shop off from the garage. Having just a speaker in the shop pretty well eliminates the dust problem. Lately I've bought an inexpensive Bluetooth speaker that does the talking for my smart phone and that has access to gigabytes of stored media and streaming radio and is also unlikely to fall to the dust gremlin.

Re: Dust vs Workshop Stereo Components

#9

Re: Dust vs Workshop Stereo Components

TomD

I hate itunes and all that jazz. I am not an apple hater, per se, but they seem to make everything simple by first making it incredibly complicated. My system is therefore based on a 35 dollar Scandisk player, and a 35 dollar (there is a theme here), home theater system I bought at walmart.

The better scandisk player is said to be slightly older versions bought NOS or refurb. Parenthetically it is the only player I have purchased that reliably runs in my F-150 sound system because it has enough output.

Nice thing about Scadisk is you can use tiny storage to bump in 32 gig or whatever you want of tunes (which presumably most readers do also). At that price point though, you get a player that runs a vast range of file formats including higher resolution ones. Save in the AVI format from you DVDs or other sources and you will have pretty good sound, if you are an MP3 snob.

I found a good basic education in current ideas on Hi-Fi by looking up Ponopod and letting the fur fly.

Re: Dust vs Workshop Stereo Components

#10

Apples and Oranges

David Yoho

William, I'm doing about the same thing with my Samsung phone. I use Google Play Music to store all my tunes on their cloud. Whenever I download music from iTunes to my computer it is automatically uploaded to Google and available to my devices. Google Play Music also has themed radio stations, much like Pandora does. I'm not sure why I still have a Pandora account anymore. I hardly use it now.

Re: Dust vs Workshop Stereo Components

#11

Re: Dust vs Workshop Stereo Components

William Duffield

I understand your negative emotions. More than once, iTunes has made decisions for me that were wrong, and caused me to waste a lot of time rebuilding audio collections on the iPad, and on my iMac. It taught me not to trust them, and especially not to trust Apple's cloud.

The other annoyance with the iPad (unlike my LG phone and most non-Apple smart phones) is that I can't put a micro-SD card in it to store and save and transfer data.

I don't worry about music formats. Neither y mobile speakers nor my old worn out ears need any higher fidelity than MP3. In the shop, I'm usually making a lot of other noise while trying to listen to the music anyhow. In the car, the acoustic environment is even more abysmal, but at least the stereo has a USB port that I can plug the iPand into. I'm sure I could do the same with my Android phone, it's just that all the interfaces to me would be different, and even less intuitive than Apple's has become.

Steve Jobs used to ride herd on the programmers developing apps to try to make sure everyone provided a consistent user interface and other basic operations, but he's not around anymore. I don't know whether its stubbornness or stupidity or something more sinister that motivates programmers to make every app work differently.

Nothing is ever as simple as it seems, and everything always takes more time and costs more. That's just as true for Apple as for Android or whatever else is out there.

Re: Dust vs Workshop Stereo Components

#12

Re: Dust vs Workshop Stereo Components

Jim in Milton, Ont

I've got XM on my phone, I Bluetooth it to a speaker I have in my shop, easy and takes up so little space... I'd never go back to stereo amps receivers etc. again.....

There are a lot of free radio apps as well, so I have a variety other than XM, love listening to baseball and hockey while I work

Take care,

Jim

Re: Dust vs Workshop Stereo Components

#13

Re: Dust vs Workshop Stereo Components

Tony-Memphis

Late to the game here, but I have a bookshelf stereo in my shop. I made a cabinet out of 1/2" mdf with a door that is an open frame. I added air holes in the back and holes for the cables. I covered everything with speaker cloth. No dust and I can still read the display and air gets through for cooling.

Tony

Re: Dust vs Workshop Stereo Components

#14

Re: Dust vs Workshop Stereo Components

don stephan

Speaker cloth - why did I not think of such an obvious approach? That's why a forum like this is such a value. Thanks!