Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

how to remove stripped screws

Posts

how to remove stripped screws

#1

how to remove stripped screws

john lucas

I remodeling an older garage into a new workshop and have everything stripped down to the walls except one cabinet. It has only 3 screws left that I can't get out. They have stripped phillips head screws. And by stripped I mean cone shaped. Not hint of threads left. I thought I would simply knock the heads off with a cold chisel but they are resisting. He must have used some stronger screws for those 3 as the other ones looked like drywall screws and in fact on head stripped off. Any ideas oh how to get these out. I've been thinking about using a pry bar from the back and hopefully pulling the screws through or breaking them off but haven't done that yet. Have to stop and make a trip to the dentist for a while so thought I would ask the guru's.

Re: how to remove stripped screws

#2

easy

Mike Farinella

On your way to the dentist, stop by a hardware store and get a screw extractor set.

Re: how to remove stripped screws

#3

Re: easy

john lucas

I have a screw extractor set. That was next. Worse thing, it might strip the head off which will work also. I also have one of those hollow drill bits to get broken screws out. Just have to find that stuff. Most of my shop is still stored in a Mobil Attic Container.

Re: how to remove stripped screws

#4

OK that didn't work

john lucas

Tried drilling the head using my official screw extractor drill. It didn't work. Then tried drilling the head with a regular drill. Ruined that drill. My hollow drill bit is too small to drill around these. If I had my metal lathe I'd just make a custom bit but it's about 14 feet deep in the container and that isn't going to happen. If I can find my drill rod in my scrap metal bin I may just try and make one using the wood lathe this weekend at a demo I'm doing. I can drill it on the lathe and then file the teeth by hand. I did find my propane torch so I can harden them afterword.

Re: how to remove stripped screws

#5

Got a Dremel tool?

Tim Greif - West of Chicago

Just cut a saw slot in the head with an abrasive wheel to accommodate a big flat head screwdriver.

Re: how to remove stripped screws

#6

Re: Got a Dremel tool?

John lucas

All of my dremel tools are packet in a box somewhere in the mobil container that has my shop My new wife has a dremel so maybe i can buy a cutoff wheel on the way home in a worse case i just cit the head off

Re: how to remove stripped screws

#7

Re: how to remove stripped screws

John Veerkamp

or use a small wood chisel and cut out the wood around the screws enough to pull the cabinet off the screws.

Re: how to remove stripped screws

#8

Re: how to remove stripped screws

Dick Coers

Take a hole saw and drill a pilot hole in a piece of scrap. Take the center drill out of the hole saw. Clamp or pin that pilot hole scrap over the screw, then drill out a plug.

Re: how to remove stripped screws

#9

What I do...

John in NM

If there is enough of the screw sticking out to grab with the smallest pair of needle nose vise grip, put those on the screw head in line with the screw axis (as in sticking straight out from whatever the screw is in).

Then take another pair of regular vise grips and clamp them nice and tight across the jaws of the needle nose pair, as close to the screw as possible. These keep the needle nose jaws from twisting off the screw.

Use the regular pair as the lever to unscrew the stuck screw.

This also works with screws torqued off below the head, but you have to do some chiseling to get enough screw shank to grab onto.

Re: how to remove stripped screws

#10

Re: Got a Dremel tool?

John K Jordan

>Just cut a saw slot in the head with an abrasive wheel...

This is exactly what I do if I can't get vise grips on the screw head. I've removed MANY philips with stripped heads from motorcycle engine casings this way!

JKJ

Re: how to remove stripped screws

#11

Re: how to remove stripped screws

Barry Irby

I have run into this more times than I care to think about. On construction jobs we had limited access to tools. Like you, I had them, but they were not handy.

Since you have spun out, essentially drill out the crew head, I would have thought you could drill the screw head off. You don't need to drill away the entire head, just the center of it, larger than the shaft of the screw. Maybe a 1/4" bit would do. Drill through, leaving the head as an ugly washer on the bit.

Next, I would try chiseling the wood away around the screw head. As a wood worker, you can fix the damage alter. (A small hole saw woudl do the trick here if you have one handy.

If all else fails or is unavailable, try brute force. Chisels, wrecking bars, sledge hammers, whatever. Pound the offending cabinet to death.

Re: how to remove stripped screws

#12

I sounds like this screw is hardened

Bill Tindall, E.Tn.

note it dulled a drill. If I could find a Dremel I would cut a slot in its head and try to screw it out.

Re: how to remove stripped screws

#13

Re: how to remove stripped screws

Keith Newton

If it is into something like old pine, heat it with a pencil torch, which will melt the resin to liquid, then it will be like a hot knife in butter.

Otherwise, I've used a 1/2" dowel cutter, to drill around them, then using a 3/4" dowel to plug the hole.

Re: how to remove stripped screws

#14

Re: I sounds like this screw is hardened

john lucas

Yea you would think if the screw heads were hard enough not to drill that they wouldn't cone out like they did. Tried 2 different drills and rounded them both over. fortunately I have a Drill Doctor so I can put an edge back on them once I find that thing in the mobil attic.

Re: how to remove stripped screws

#15

thanks everyone.

john lucas

Gonna go out in a few minutes and try the Dremel trick. If that fails I'll either carve around the screws or use a hole saw to get enough clearance to try the vice grips. The problem is they are about an inch or so from the top of the cabinet so gripping them with needle nose vice grips are about the best I'll be able to do. If that fails I'll use the hole saw without the center drill and just drill through the 3/4" board so the cabinets can come off the wall and leave the screw there until I can pull it out with other means.

Re: how to remove stripped screws

#16

There are other things to cut the cleat,

Keith Newton

If you have a multi-tool, cutting close on each side will work.

If you are a good at slowly rocking into the wood with either a jigsaw, or reciprocating saw, those are handy.

If you still find it too tight, and don't have a pencil torch handy, I'd try a fireplace lighter. It won't get as hot, but maybe hot enough.

Oh oh oh! another good easy thing, is to just chisel out enough wood to get the chuck of you drill over the screw, then tighten the keyless chuck into the outer edge of the screw head, then hit reverse. I've done this with screws where the head broke off, and the chuck will really get a good grip on just threads.

Re: how to remove stripped screws

#17

lots of good ideas, non of them worked

john lucas

Well actually the crowbar did. I cut a slot in the screw head. That just stripped out even with a freshly sharpened flat blade screwdriver. I could not get a hole saw to run true without the center drill. It just wanted to run. I don't have a multitool (oh boy a new tool to buy). Tried cutting away the wood with a Dremel and grabbed it with both needle nose and regular vice grips. No go, they just slipped off no matter how tight. You couldn't get to it from the side. Tried a cold chisel and 3lb hammer. All it did was bend the screw.

So I finally pried with the crowbar enough to get a rope around it. Tied it off to the truss's. Then pried it free. Unwrapped the ropes enough that I could lower it to the ground. This thing is 9 feet long and Oak. Once I got it down I put a dolly under one end and picked up the other and drug it to my wood storage shed where it will sit until I decide where to put it back up.

Re: how to remove stripped screws

#18

Ahh! Success.....

Barry Irby

Glad you got it.....I had one more idea....light saber.....uhh, reciprocating saw. Its one of my favorite demo tools. Put a long metal cutting blade in it and run it behind the cabinet or under the cleat and cut the screws.

Now on to the next thing.

Re: how to remove stripped screws

#19

Ps, a question.....

Barry Irby

How was it those screws were so soft you coned out the heads and then stripped them when you cut a slot in them, but so hard you could not drill the heads off?

Re: how to remove stripped screws

#20

Re: Ps, a question.....

john lucas

Barry Still don't understand that. When I got the cabinet off (with screws still sticking out) they appeared to be standard drywall screws. I did some grinding on one just for the hell of it. The outer portion was moderately soft which is why the slots stripped out. The center was very hard which is of course where the center of the drills could not penetrate. I did notice when I first started to drill it seemed to cut away some of the phillip slots but then simply stopped. So how did they get that way? who knows.