Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

bearing replacement problem

Posts

bearing replacement problem

#1

bearing replacement problem

Bill Tindall, E.Tn.

Tool- Bosch 7617 router had a bearing that screeched occasionally, especially during starting

The large load bearing bearing on the bottom of the shaft was a NTN 6004LB. This bearing has "noncontact" seals, what ever noncontact means.

The local bearing store recommended a replacement SKF608 (costing5X the price of what was in there. I heated the router housing to 200 F and cooled the bearing to 15 F and the bearing dropped into its housing, then locked up upon cooling.

Assembled router uneventfully. After assembly the shaft turned freely but with a bit more friction than before. That is to say before if I spun armature it would coast a slight amount and now it doesn't. The new bearing is just stiffer, but smooth. The bearing store said the old one had lost its grease.

Did a test run and after a minute the shaft where the bit goes was hot. Don't know why. I don't think it used to get hot.

Re: bearing replacement problem

#2

Re: bearing replacement problem

John in NM

I've had them do that, though in somewhat lower speed applications than a router. At a guess the grease in the bearing needs some running to push it off to the side so that it's not in the way of the balls running around the race.

I'm more confused by the bearing numbers - those are two quite different size bearings if I'm reading correctly. 608's ought to cost around $4 from most suppliers online, maybe twice that from a retail store.

Re: bearing replacement problem

#3

Re: bearing replacement problem

markhennebury

Hi Bill,

The different shields used in bearings offer different values. The non-contact seals ( Z, 2Z) are metal shields, they only contact one part of the outer ring of the bearing, therefore produce less friction, and heat, and can run at higher rpm, but they sacrifice sealing the dust out, and they loose grease quicker. You probably have replaced the bearing with one with rubber seals (2RS ) which contact and seal to both inner and outer ring of the bearing and would account for a more firm feel and a higher heat. You can check the number and seal type on the bearing and check for the maximum allowable rpm, to see if its a suitable replacement anytime that you replace bearing.

Link to skf;http://www.skf.com/ca/en/products/bearings-units-housings/ball-bearings/deep-groove-ball-bearings/single-row-deep-groove-ball-bearings/single-row/index.html?page=3


Re: bearing replacement problem

#4

Aha!It is a RS bearing

Bill Tindall, E.Tn.

with high friction. I took it out and put the old one back in for now. Will return to bearing store better informed.

Re: bearing replacement problem

#5

Thankyou

Bill Tindall, E.Tn.

with the help of the link I found the bearing I need. I was sold a bearing unsuitable for a router running at 18,000 rpm, at a cost of $29.

Re: bearing replacement problem

#6

Ummmm....

Brian Roberts

Me thinks it's time for a new bearing store.

Re: bearing replacement problem

#7

you'r welcome... another thing to watch for

MarkHennebury

Is the internal clearance.

Part of the bearing number tells the internal clearance.

Some bearings are made a loose fit and wont get to proper tolerance until they get hot, others are a tighter fit and are more accurate from the get go, suitable for machines that don't run continually. If there is no internal clearance marked on the bearing than they are Standard Clearance or C0. Standard clearance is not usually marked on the bearing. Quite often i have found that the bearing shops will sell you C3 bearings, when you haven't requested them, C3 is a loose fit internal clearance. So it is always good to check the manual that came with the machine to see what is recommended, then always check that the bearing supplier is supplying what you have asked for.

As a general rule of thumb... don't trust what you are told, always check and confirm.


Mark

Re: bearing replacement problem

#8

I manufactured bearing seals

Ron in Sterling, CT

when I worked for a living, especially for SKF. While the RS seal is a good seal, it creates way to much friction at router speeds. As a matter of fact, I replace the bearings in my router with shielded bearings. They don't last as long because as stated before dust can get in easier, and grease does run out of them, but there is virtually no friction, and as a consequence, no heat generation. I relube them a couple of times with a syringe, then replace them. Get the right bearing, and you will have no problems. Good luck.

Ron

Re: bearing replacement problem

#9

Re: bearing replacement problem

Jesse Cloud

Really interesting thread with lots of useful info.

This would make a great article for future reference.

Re: bearing replacement problem

#10

Good article indeed...

John in NM

Maybe print it out and give it to that bearing shop :D

Seriously though, I never knew this about rubber seals - I see now why a lot of tool manufacturers use shielded instead, even though they wear out quicker. Never too old to learn something I guess :D