Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Sizing Allen Wrenches

Posts

Sizing Allen Wrenches

#1

Sizing Allen Wrenches

don stephan

Having a number of unlabeled allen wrenches, I searched the Internet yesterday without success for a sizing tool that would identify the size of SAE and metric allen wrenches. The only solution I found was a set of labelled allen head screws. Has anyone found such a gauge tool?

Re: Sizing Allen Wrenches

#2

Re: Sizing Allen Wrenches

John Veerkamp

what's wrong with a micrometer?

Re: Sizing Allen Wrenches

#3

Re: Sizing Allen Wrenches

Lee Schierer in McKean, PA

SAE allen wrenches come in .050, 1/16, 5/64,, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4, 5/16, and 3/8. There are larger sizes as well, but you just need to measure across the flats.

Metric sizes in mm are: 1.5, 2, 2.5, 3, 4, 4.5, 5, 6, and 7. Again there are larger sizes, but you can measure them with micrometers or calipers.

Lee

Re: Sizing Allen Wrenches

#4

Re: Sizing Allen Wrenches

don stephan

Measuring with a micrometer certainly is an option, but doesn't seem as fast as testing with a gauge. Maybe it's just me. I'll have to make a chart of decimal equivalents and see what it looks like.

Re: Sizing Allen Wrenches

#5

ummmmm.....

Brian Roberts

do you have hundreds of them to check?

A simple caliper will do fine....no need for a mic

Re: Sizing Allen Wrenches

#6

Re: Sizing Allen Wrenches

mdclor

Don, don't use my system which is: Look at the bolt, walk to the drawer where they are all stored loose, paw around until I find the 3-4 that look to be close, walk back to the bolt, try them one by one, walk back to the drawer....... :D

Its a good thing that I'm retired and have the time to play that silly game. I'm with you, they make sets for checking the sizes of nuts and bolts, why not for allen wrenches?

Re: Sizing Allen Wrenches

#7

Re: Sizing Allen Wrenches

Bill Howatt

I have an Allen wrench holder and it has holes to place each of the different sizes. I can just poke an unknown wrench into a hole until it is the last one that fits. Unfortunately, I can't tell what the numerical size is when looking at a bolt head so I just attack it with several from my collection.

Bill

Re: Sizing Allen Wrenches

#8

Re: Sizing Allen Wrenches

Hank Knight

I've used mdclor's system for years, even before I retired. Works for me. :D

Seriously, though, in addition to a bunch of loose ones, I have two sets of allen wrenches that I use most often, one metric and one imperial. They came in plastic clips that have the sizes printed for each wrench. I keep them in the clips, but I can't say the size ID helps much. I still have to guess at the correct size and use the trial and error selection method to settle on the correct wrench.

Re: Sizing Allen Wrenches

#9

Re: Sizing Allen Wrenches

William Duffield

I use Hank's system, after using mdclor's system for years, but I have also enhanced it a bit. In addition to the two sets in plastic holders, I have another set with clearly labeled plastic handles. TheI found thazt these are not nearly enough to keep me from wasitn a lot of time, so the next improvement is to write the Allen wrrench size on the tool or machine next to the bolts. In a few cases where I'm adjusting a particular bolt a lot, I now also have 1/4" hex drive Allen bits or sometimes just an Allen wrench attached to the machine near the bolt with a small rare earth magnet. Now, all I need to do is find the driver handle or the battery powered drill.

Re: Sizing Allen Wrenches

#10

Re: Sizing Allen Wrenches

Jesse Cloud

I use mdclor's system as well, with a couple of riffs.

1. There is one size which fits a lot of stuff. I have marked it for easy recognition.

2. If I am using the Allen wrench for a stationary tool or a large portable, I approach the tool with a handful of spare Allen wrenchs and a small rare earth magnet. When I find the right wrench, I leave it attached to the tool with the magnet.

Re: Sizing Allen Wrenches

#11

Re: Sizing Allen Wrenches

Tom Pilsbury (Chicago)

Maybe the Handyman Club of America will send you one. :D

Re: Sizing Allen Wrenches

#12

Maybe a better idea than you think

Henry Higginbotham

Take one the rare, collectible white spaghetti sizers and a set of known hex wrenches. See what fits where. Label accordingly.

Re: Sizing Allen Wrenches

#14

In a pinch, I have found,

Keith Newton

that sometimes I've been out on a job site, or down at the cabin, doing some job without all the tools in my chest back at the shop, that the 6 point star, or torx bits that are part of an assortment roll that I keep in my Makita drill / driver bag, will do the job. So far, it had not failed me yet

Re: Sizing Allen Wrenches

#15

Kneale Brownson

Re: Sounds like a job for one of these: *LINK*

Kneale Brownson

Cordless Engraver Tools


img

One Source

Re: Sizing Allen Wrenches

#16

Jim DeLaney, Austintown, Ohio

Re: ummmmm.....

Jim DeLaney, Austintown, Ohio

Actually, a simple vernier caliper would be especially better than a mic where there's a mix of Imperial and Metric, since most calipers have both scales on them.

Re: Sizing Allen Wrenches

#17

Am I the only one?

John in NM


Mine are all in a handy sized holder that came with the set :D

If I were sorting a bunch of unmarked allens, I would use a mic, but for daily use I have about zero patience for anything but one of these sets.

I used to be able to read the size right off the wrench (good ones are marked) but those days are long gone.

Re: Sizing Allen Wrenches

#18

#2 works for chuck keys too...

John in NM

And a machinist square stuck to the side of my jointer.

There ends the actual uses I've found for those nifty little magnets :D

Re: Sizing Allen Wrenches

#19

Nope. That's what I use


Re: Sizing Allen Wrenches

#20

I have a can.....

Bill Tindall, E.Tn.

I have a can with many dozen Allen wrenches in it. In exasperation I bought a fraction and metric version of what you have. Would anybody be interested in a can of Allen wrenches to measure. The price is right!

Re: Sizing Allen Wrenches

#21

Re: I have a can.....

Stuart Johnson

I have two sets each metric and fraction but still don't do much better than fishing around in a can. I can't look at an Allen screw and think "that's a nbr. 10 or it's a 5/16. Instead it's a this one is too tight and the next is too loose so I try the other kind. With luck the first one will be the correct size unless of course the screws are very cheap imports that fell within the 10 % over under sized manufacturing specs.