Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

WC Weekend Accomplishments....

Posts

WC Weekend Accomplishments....

#1

WC Weekend Accomplishments....

Dennis E Peacock

27 July 2015

Good Morning Everyone,

I hope this finds each of you doing well. It's been really hot here as well as humid. The humidity, at times, has been seemingly thick enough to cut it with a knife. Talk about breathing heavy air.!!!! I truly don't know how the folks in Arizona do it, with the high heat they have during the summers.

The guitar project is in the finishing phase and we decided to take off the stain colors and go with a paint finish instead. This is in part, due to the pick guard and pickup colors/styles we purchased. So...we are using an automotive acrylic lacquer for the paint and clear coat finish on the guitar bodies. Been working a lot at the day job and we are losing a person off of our team and that's really going to hurt because it's not easy to find someone that wants to work in the line of work we do. Right now, we're not even sure we will be allowed to hire anyone, as we are still waiting to hear if we can or not.

That's it for me, so what did YOU do this past weekend?

Best of weeks to you all.

Dennis Peacock

Re: WC Weekend Accomplishments....

#2

Re: Brought Home a New Toy

William Duffield

I drove almost 800 miles yesterday and today to pick up a Powermatic 15HH planer. I had great help at the other end disassembling and loading it into my xB. It's now at my home, but this adventure is just beginning. Even though it is now in pieces, at over 500 lbs, I'll need more help unloading and setting it up in my shop, but only after I find a new home for the DW733 it's replacing. I'll need to make some additional arrangements, because it will require quite a bit more room, especially since the cast iron infeed and outfeed tables don't fold up when it's not in use.

Re: WC Weekend Accomplishments....

#3

Re: Brought Home a New Toy *LINK*

Grant in Iowa

Bill,

I recall when I made the move to a 15" planer. I realized shortly after the purchase that I would either need to add an accessory, or change my method of work.

I had a DeWalt DW733 too, and the one thing it did well than my larger 15" Delta was to take off a small amount of material to aid in fine fitting of parts. My method of work had become to create the dados for a project, then fine tune with the planer the pieces to fit in the dados. This approach could not be effectively done with the new 15" planer, mostly because of the serrated infeed roller. The infeed roller causes hatch marks on the work piece, necessitating the removal of a larger amount of material. For some time, I kept the lunchbox planer as a solution.

Then I found the Wixey digital planer depth gauge. One I got it installed and aligned, I found the new planer to be a dream to use. I can now confidently plane stock to the desired thickness while still removing that "required" amount on the last pass. It is actually very convenient to be able to plane off...say an even 1/32" per pass, or 1/16", or even one ten thousandth if need be. It is also convenient when the inevitable need to create an additional piece of stock after a miss-cut or flaw in a work piece is found.

When I bought mine, it was an older version that ate batteries like I eat twizzlers. Then Wixey came out with a new version, and when I contacted them with a question, they offered to send me the new version for no charge. Great company, great product. I wouldn't have a planer without it now.

No affilliation with Wixey, just impressed with their products and customer service enough to want to share the good experience.

Regards,

Grant in Iowa


PM 15hh installation image at Wixey

Re: WC Weekend Accomplishments....

#4

Re: Brought Home a New Toy

William Duffield

Thanks for the link. I will need to reinstall the gauge. I appreciate your advise; without it, I probably would have delayed learning how to use the Wixey, and continued to use my old method, which relied on the depth being set on my 4" double square. I have used a few planers of the same design as the PM, and I am aware to the problem with the roller. I found out a long time ago that I can't remove the final 64th of an inch with it.

I also found out that the DW733 is not robust enough to take off a 16th of white oak on an 11" wide 16/4 plank, even though it is very good at finishing narrower boards without snipe. Some of the Amazon reviews point out serious problems with it: if you overload it, you can stretch the drive chains and break sprockets. As nice a finish as it leaves, it is still in need of improvement, with either a sander or a well tuned smoothing plane.

On the big planer, the only effective ways I've found to avoid snipe is to allow and extra 5" on the front and back ends of the boards, or have a couple of pieces of scrap, one to preload the infeed roller, and another to "postload" the outfeed roller.

Wixey makes some really useful and accurate measurement tools. I find that the Wixey combo angle gauge and level with the tilting display is a very useful tool.

Re: WC Weekend Accomplishments....

#5

Re: Brought Home a New Toy

Grant in Iowa

Bill,

I have been able to (largely) avoid snipe on both of my planers by ever so slightly elevating the ends of the infeed and outfeed tables. I would think that can be done on your cast iron tables by inserting a piece of paper in the lower side of the joint between the planer and the table before snugging the bolts. I'm not talking about a lot here, maybe a 16th of an inch or maybe slightly more. Check your setting with a straight edge run through the planer throat. My Delta has the roller in and outfeeds, which give slightly under the weight of material being planed. The higher in and outfeed tables sort of make up for the flex, resulting in better results.

Your mileage may vary, as your cast iron tables might not flex as much (insert envious look here) as my rollers. I do suggest you spend/ invest some time making slight adjustments to get it dialed in. It can be configured to not snipe, unless the wood hasn't been face jointed first.

Regards,

Grant in Iowa

Re: WC Weekend Accomplishments....

#6

Re: Brought Home a New Toy

William Duffield

If I remember correctly from the last time I set one of these up, under each bolt holding the table in place is a set screw to do the fine adjustment on the height of the ends of the tables. And yes, cast iron parts on planers, table saws, etc. do flex less than rollers, stamped steel tables, etc., but cast iron has a few disadvantages as well.

Re: WC Weekend Accomplishments....

#7

infeed rolls

Bill Tindall, E.Tn.

If you are denting surfaces with a light cut your infeed roll pressure is too high. I don't dent with my 18" machine.

Re: WC Weekend Accomplishments....

#8

snipe

Bill Tindall, E.Tn.

I don't get snipe with my 18" Powermatic.....when it is set up correctly.

Re: WC Weekend Accomplishments....

#9

Its as easy as the settings...

John in NM

Powermatic used to have a great little book they'd send you on proper set up. Don't know if they will still do that.

Do you find that optimized for no snipe you have less ability to make heavy cuts? I have my 12" set to kind of balance the two, but honestly I take more than 1/8" so rarely that I should probably just not bother splitting the difference. Next time (soon) I change the blades maybe.

Re: WC Weekend Accomplishments....

#10

no snipe on an industrial quality machine

Bill Tindall, E.Tn.

The bed rollers need to be set low (waxing the bed helps in this situation) and the pressure bar set so low that it almost interferes with feed. I set the pressure bar empirically. If it is not dragging and impeding feed I lower it until it does and then back off a small amount. I get no snipe.

If your machine does not have a pressure bar it may not be possible to avoid snipe. For this reason I think an old 12 or 13" cast iron Powermatic or Delta is a better machine than any of the modern "inexpensive" planers.

Re: WC Weekend Accomplishments....

#11

Re: infeed rolls

William Duffield

I don't understand how you can get both at the same time. If you adjust your infeed pressure low enough to not leave marks from the toothed infeed roller and antikickback pawls when taking off the final 64th on soft woods, then the pressure is so low that you get snipe when feeding long, heavy stock. You can minimize the problems only by using finely adjusted outboard roller stands, if you can convince your helper to not touch the stock while it's under the cutter head. At least I've never seen one of these so finely adjusted that you avoid both problems. Of course, no one is going to stop in the middle of a job and adjust the roller pressure. Nor is anyone going to accurately adjust outboard roller stand heights after every pass.

In my mind, the most serious disadvantage of this planer design is that the table moves up and down instead of the cutter head, so roller stands are ineffective or a PITA to use, especially when you are working by yourself. I understand why it is done. Otherwise, the motor would need to be mounted on top of the machine, which makes it really difficult to pass stock back to take the next pass.

Re: WC Weekend Accomplishments....

#12

Easy way around the bed rollers....

John in NM

Make a removable smooth bed that sits on the rollers. A waxed piece of 8/4 with a cleat on the front bottom works well.

The snipe I get is minimal, not enough to cause problems, but it is there. A few thousandths I would guess, but I've never measured it. I recall trying to remove it entirely when I bought the machine (a PM100), but finding that my current set up minimized snipe while keeping feed problems out of the picture.

This 12" is a simplified version of yours. Setting pressures can be done, but as I recall there is something different about how it is done. I would have to look at the diagrams again to remember.

Re: WC Weekend Accomplishments....

#13

Train wife

Bill Tindall, E.Tn.

In the course of selling hardwood lumber we have shoved tens of thousands of bdft of lumber through the Powermatic. If there is more than a board or two to do wife is the off bearer. We don't get snipe. It would have been a fatal defect in our sales and unacceptable in machining furniture parts.

I have never seen a need to remove 1/64" from a board. 0.020" is about as little as I ever go in finish dressing and that is rare. 0.025 to 0.050 (approx.) is more common finish cut.

Know the thickness of what you got. A digital caliper is essential. Know how much thickness is reduce per revolution of the thickness adjuster. There is no problem hitting any target when starting from rough lumber or oversized lumber, without resorting to tiny increments on the last cut.

Re: WC Weekend Accomplishments....

#14

Re: Train wife

William Duffield

My wife is incorrigible. I don't think there is any way I could train her to help me dimension boards. ;)

I'm going to need to start using the thickness gauge. The new planer is equipped with a digital unit by Wixey, which by all accounts is very accurate (or can be, once calibrated). The way I have been doing it was to set the target thickness on a 4" double square (A 6" or a combination square would work almost as well) and use it to measure the thickness every time the board came off the planer. That way, I didn't need to memorize any numbers. When the remaining thickness got less than the amount I was taking off at a pass (typically one full rotation of the adjustment wheel), I would adjust the last pass based on how much I had left to remove. Sometimes it was a 64th. I have been improving the process somewhat lately however. If I see that there is only one more standard pass plus 1/64 left to be removed, I crank the depth adjuster a quarter turn less than a full pass, so the next, last pass is always assured to be thicker than the amount that would leave roller marks.

I'm not too old to be retrained yet, even when I've learned a method that has worked just fine for me for years.