Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Bugs in Oak questions

Posts

Bugs in Oak questions

#1

Bugs in Oak questions

Barry Irby

A couple of years ago a 42" diameter white oak tree fell on my rental house. ($24,000 in damage, nobody hurt) I saved the log and had it quarter sawn and stacked it in my driveway under a cover. I have found that a little of it is spalted. I think the tree had an injury on one side, exposing the wood. Today I pulled out a piece and dressed it. Not only was it spalted, it had bug holes in it. They are about a 1/16" in diameter. I am guessing they are powder post beetles holes.

I was making a threshold and did not want it spalted or bug eaten, so I laid it aside and pulled out another piece that was sound and used that.

Been thinking about the bugs. Exit holes are round. These were not. Every thing but round. I have not seen any frass. The holes are "aged" looking, not freshly cut. All this leads me to believe the bugs were in the wood before it was sawn and there has been no activity since. Any thoughts? What would you do?

Re: Bugs in Oak questions

#2

Sounds Like

Mark Mandell - Gone Round In New Jersey

"kindling" to me.

The stuff just ain't that precious.

Re: Bugs in Oak questions

#3

Re: Bugs in Oak questions *LINK*

Grant in Iowa

Hi Barry,

Odds are you are encountering Powder Post Beetle (PPB) tunnels. I will defer on the details to Bill, but it goes something like this:

I get them showing up in my air dried lumber from time to time before it dries completely. Even after it dries, the larvae will still mature and emerge as beetles to seek out a new place to burrow and lay eggs. Also, if you are seeing "frass", or little piles of fine sawdust under your lumber stack, it can mean the insects are active, or it can also mean the lumber has simply dried sufficiently to allow the powder to sift our as the pile gets banged during lumber sorting.... so don't panic.

So what I think you are seeing, assuming your lumber has been drying for some time, is the signs of the beetles emerging. The beetles are finicky about where they will lay new eggs, so once the wood dries below about 12% or so, they won't lay eggs in it any longer. Here in Iowa, due to very humid summers, I keep my dried lumber inside my air conditioned shop. I end up with a pretty even 10 or 11% moisture content in my lumber year around this way. This also helps keep the moisture content of the lumber similar to what it will be in finished form inside my air conditioned home.

Of course this is one very good reason to kiln dry your lumber. Kiln drying not only brings the Moisture Content (MC) low enough as to make the lumber undesirable to the insects, but the kiln operator can raise the kiln temperature high enough to kill any insects inside, though this is not always done.

If you store your lumber long term, do so off the floor as much as possible, and under cover in a drafty but not open building. Better yet in a modern building that is conditioned similar to a home.

Just because you have kiln dried lumber, doesn't mean it will stay below the moisture threshold, as that is more a matter of proper storage in a dry area.

I don't think it is a reason to panic, as they will naturally leave the wood once it dries, and the damage is already done when they enter the wood and lay eggs, so to speak. if you would like, there are products you can treat your wood with, such as Boracare, and others. I know Bill talks about dipping the stack of lumber in a product at the mill, but that requires the right setup to do.

I am by no means an expert, but I have been doing logs to lumber for around fifteen years now. I think lumber with PPB holes in it can add character to the right project, so I don't discard it just due to the holes. Sure, there are traditional furniture projects on which you would not do that, but there are plenty of other styles of projects that it can add a little something.

Here's a link to basic information about the subject

Regards,

Grant in Iowa


PPB's at Iowa state university

Re: Bugs in Oak questions

#4

Up close and personal

John K Jordan

I am one with the distinct honor of witnessing PPBs both entering and exiting wood. Once chainsawing and coating chunks with Anchorseal I watched little bugs apparently attracted to the smell of the fresh maple fly up, land, and immediately start chewing into the wood. They were quite efficient at making holes!

Some years before I had 2" walnut squares stacked on a shelf next to my lathe, about ear height. A friend had given me some that had been stacked outside. I kept hearing a soft "skritch, skritch" coming from somewhere around the walnut and while investigating I saw a PPB break through the end grain! What are the chances?! I took that wood out of the shop.

I've had some in green poplar in my barn but not in much else. The holes I've seen are always round. If the holes you saw were elongated, I wonder if they were in the wood before it was cut and the cut was at a diagonal to the round hole. But I certainly haven't studied PPB holes carefully so this is nothing but speculation.

JKJ