Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Wood hardner/epoxy

Posts

Wood hardner/epoxy

#1

Wood hardner/epoxy

Dale warder

Several years ago I used a wood conditioner/hardener which penetrated soft or decayed wood in order to avoid replacement of the decayed wood. It was advertised as a product penetrated deeply into the wood and hardened. It was a 2part product of low viscosity. As I remember it, this was made by Minwax.

I have several chairs which have casters on the bottom of the legs. Over the years, the end of the legs have become soft. I m considering using such a product to harden the leg before reinstalling the casters.

Does anyone know of a current supplier of such a product?

Does anyone have experience doing this with chair legs?

Note, the last time I remember the Minwax product was 25+ years ago.

Thanks,

Dale

Re: Wood hardner/epoxy

#2

Re: Wood hardner/epoxy *LINK*

Hank Knight

Never used it, so I can't answer your question qnout chair legs, but:


Minwax Wood Hardener

Re: Wood hardner/epoxy

#3

A quick search

Brian Roberts

online for "Minwax® High Performance Wood Hardener"

shows it is sold by several of the big box stores.

Re: Wood hardner/epoxy

#4

I'd suggest epoxy instead

Dick Coers

That Minwax product is like 75+% solvent. It's not dissimilar to plexiglas dissolved in acetone. You won't get penetration in a chair leg like you would in rotten wood. Epoxy will be structural, wood hardener wont.

Re: Wood hardner/epoxy

#5

Re: I'd suggest epoxy instead

Brian Roberts

Sorry...but if the wood hardener won't penetrate then epoxy surely won't.

Re: Wood hardner/epoxy

#6

Maybe what I should have said,

Dick Coers

was the solids in the Minwax hardner might not get into the cells like in punky wood. The solvent sure will. I still don't think that is the product to strengthen a chair leg.

Re: Wood hardner/epoxy

#7

Re: System 3 RotFix

William Duffield

http://www.systemthree.com/store/pc/Rot-Fix-c39.htm

If you have wood that's so far gone that stabilizing it isn't enough, then you will need to fill the rotted areas with a structural epoxy. System 3 offers those as well.

Re: Wood hardner/epoxy

#8

call   Minwax  and ask ?


Re: Wood hardner/epoxy

#9

Re: System 3 RotFix

Roy Girolami

I used the Minwax to repair a window sash. You are supposed to remove all the rotten wood you can and then put the thin hardener on where you removed the wood . Then you use the thick part to build the wood back up like Bondo does for a car. It worked okay for painted wood.

Roy G

Re: Wood hardner/epoxy

#10

Reinforce first?

John K Jordan

If the leg end softening is a structural concern, I would consider a structural reinforcement.

It's hard to know if this would be practical without seeing it, but if the caster slides into a hole drilled into the end of the leg and if there is enough wood in the cross section, I might consider drilling the hole to a larger diameter and epoxying in a steel tube that the caster can slide into. The reinforcing tube could extend much further into the leg than the caster, into sound wood further from the end. Then perhaps you could use wood hardener to treat the outer surface of the wood.

Are these chairs around a table with wooden legs? Easier fix! :-) Cut a few inches off each leg of chairs and table and when your wife says something doesn't feel right tell her she must be must be losing it. (Put on protective gear first.)

Re: Wood hardner/epoxy

#11

Re: System 3 RotFix

William Duffield

From your description, it sounds like the two systems are very similar. Since I have not used both, I couldn't make a fair comparison, to say which one might work better.

Re: Wood hardner/epoxy

#12

Re: Wood hardner/epoxy

Dale warder

Thanks to all who replied to my problem. Much good information and suggestions

It seems all agree that the current Minwax Wood Hardner is not appropriate for this. As it is not an epoxy, it has little hope of providing strength. Two penetrating epoxies have been suggested, System 3 Rot fix and Aberlon Liquid Wood. I think I will order one and experiment.

Thanks for the help

Dale